G200E Datasheet, PDF (2/2 Pages) MicroPower Direct, LLC – Low Cost, 2W Compact MiniDIP DC/DC Converters

Model Selection Guide
Model
Number
G201E
G202E
G203E
G204E
G205E
G206E
G207E
G208E
G211E
G212E
G213E
G214E
G215E
G216E
G217E
G218E
G221E
G222E
G223E
G224E
G225E
G226E
G227E
G228E
Input
Voltage (VDC)
Current (mA)
Nominal Range Full-Load No-Load
5
4.5 - 5.5
494
30
5
4.5 - 5.5
488
30
5
4.5 - 5.5
476
30
5
4.5 - 5.5
476
30
5
4.5 - 5.5
488
30
5
4.5 - 5.5
482
30
5
4.5 - 5.5
470
30
5
4.5 - 5.5
470
30
12 10.8 - 13.2 203
15
12 10.8 - 13.2 201
15
12 10.8 - 13.2 196
15
12 10.8 - 13.2 196
15
12 10.8 - 13.2 201
15
12 10.8 - 13.2 198
15
12 10.8 - 13.2 194
15
12 10.8 - 13.2 194
15
24 21.6 - 26.4 100
8
24 21.6 - 26.4 99
8
24 21.6 - 26.4 97
8
24 21.6 - 26.4 97
8
24 21.6 - 26.4 99
8
24 21.6 - 26.4 98
8
24 21.6 - 26.4 96
8
24 21.6 - 26.4 96
8
Voltage
(VDC)
5.0
9.0
12.0
15.0
±5.0
±9.0
±12.0
±15.0
5.0
9.0
12.0
15.0
±5.0
±9.0
±12.0
±15.0
5.0
9.0
12.0
15.0
±5.0
±9.0
±12.0
±15.0
Output
Current
(mA, Max)
400.0
222.0
167.0
133.0
±200.0
±111.0
±83.0
±67.0
400.0
222.0
167.0
133.0
±200.0
±111.0
±83.0
±67.0
400.0
222.0
167.0
133.0
±200.0
±111.0
±83.0
±67.0
Current
(mA, Min)
40.0
23.0
17.0
14.0
±20.0
±12.0
±9.0
±7.0
40.0
23.0
17.0
14.0
±20.0
±12.0
±9.0
±7.0
40.0
23.0
17.0
14.0
±20.0
±12.0
±9.0
±7.0
Load
Regulation
(%, Max)
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
Efficiency
(%, Typ)
81
82
84
84
82
83
85
85
82
83
85
85
83
84
86
86
83
84
86
86
84
85
87
87
Fuse Rating
Slow-Blow
(mA)
1,000
1,000
1,000
1,000
1,000
1,000
1,000
1,000
500
500
500
500
500
500
500
500
250
250
250
250
250
250
250
250
Notes:
1. Output load regulation is specified for a load change of 10% to
100%.
2. These units should not be operated with a load under 10% of
full load. Operation at no-load may cause damage to the unit.
3. These converters will operate without external components.
However, when measuring output ripple, it is recommended
that an external ceramic capacitor be placed from the +Vout
pin to the -Vout pin for single output units and from each out-
put to common for dual output units. An input capacitor will
enhance stability over temperature and input line variations.
Recommended capacitor values are given in the table below.
For applications requiring very low output noise levels, a simple
LC filter should be effective.
Vin
Input
Capacitor
Vout
Output Capacitor
Single Dual
5 VDC 4.7 µF 5 VDC 10.0 µF 4.7 µF
12 VDC 2.2 µF 9 VDC 4.7 µF 2.2 µF
24 VDC 1.0 µF 12 VDC 2.2 µF 1.0 µF
15 VDC 1.0 µF 0.47 µF
Derating Curve
Mechanical Dimensions
4. Dual output units may be connected to provide a 10V, 18V, 24V
or 30 VDC output. To do this, connect the load across the posi-
tive (+Vout) and negative (-Vout) outputs and float the output
common
5. It is recommended that a fuse be used on the input of a power
supply for protection. See the Model Selection table above for
the correct rating.
Pin Connections
Pin Single Dual
1 -Vin
-Vin
7
NC
NC
8 -Vout Common
Pin Single
9 +Vout
11 No Pin
14 +Vin
Dual
+Vout
-Vout
+Vin
Notes:
• All dimensions are typical in inches (mm)
• Tolerance x.xx = ±0.01 (±0.25)
• Pin 1 is marked by a “dot” or indentation on the top of the unit
MicroPower Direct
www.micropowerdirect.com
292 Page Street Ste D Stoughton, MA 02072 • TEL: [phone] • FAX: [phone] • E-Mail: [e-mail]