D200RW Datasheet, PDF (2/2 Pages) MicroPower Direct, LLC – Miniature SIP, 2W Wide Input Range DC/DC Converters

Model Selection Guide
Model
Number
Input
Voltage (VDC)
Current (mA)
Nominal Range Full-Load No-Load
D201RW 5
4.5 - 9.0
492
15
D202RW 5
4.5 - 9.0
571
15
D203RW 5
4.5 - 9.0
555
30
D204RW 5
4.5 - 9.0
547
30
D205RW 5
4.5 - 9.0
571
20
D206RW 5
4.5 - 9.0
533
25
D207RW 5
4.5 - 9.0
533
25
D208RW 5
4.5 - 9.0
563
60
D211RW 12 9.0 - 18.0
205
15
D212RW 12 9.0 - 18.0
216
15
D213RW 12 9.0 - 18.0
208
15
D214RW 12 9.0 - 18.0
213
15
D215RW 12 9.0 - 18.0
222
15
D216RW 12 9.0 - 18.0
208
15
D217RW 12 9.0 - 18.0
210
15
D218RW 12 9.0 - 18.0
219
30
D221RW 24 18.0 - 36.0
98
8
D222RW 24 18.0 - 36.0 108
8
D223RW 24 18.0 - 36.0 104
8
D224RW 24 18.0 - 36.0 104
8
D225RW 24 18.0 - 36.0 106
8
D226RW 24 18.0 - 36.0 104
8
D227RW 24 18.0 - 36.0 104
8
D228RW 24 18.0 - 36.0 106
20
D231RW 48 36.0 - 72.0
48
6
D232RW 48 36.0 - 72.0
56
6
D233RW 48 36.0 - 72.0
53
6
D234RW 48 36.0 - 72.0
53
6
D235RW 48 36.0 - 72.0
56
6
D236RW 48 36.0 - 72.0
53
6
D237RW 48 36.0 - 72.0
52
6
D238RW 48 36.0 - 72.0
55
12
Voltage
(VDC)
3.3
5.0
12.0
15.0
±5.0
±12.0
±15.0
±24.0
3.3
5.0
12.0
15.0
±5.0
±12.0
±15.0
±24.0
3.3
5.0
12.0
15.0
±5.0
±12.0
±15.0
±24.0
3.3
5.0
12.0
15.0
±5.0
±12.0
±15.0
±24.0
Other input/output combinations are available
(i.e. 9.0 VDC). Contact the factory for details at:
[e-mail]
Output
Current Current
(mA, Max) (mA, Min)
500.0
125.0
400.0
100.0
167.0
42.0
133.0
33.0
±200.0
±50.0
±83.0
±21.0
±67.0
±17.0
±42.0
±10.0
500.0
125.0
400.0
100.0
167.0
42.0
133.0
33.0
±200.0
±50.0
±83.0
±21.0
±67.0
±17.0
±42.0
±10.0
500.0
125.0
400.0
100.0
167.0
42.0
133.0
33.0
±200.0
±50.0
±83.0
±21.0
±67.0
±17.0
±42.0
±10.0
500.0
125.0
400.0
100.0
167.0
42.0
133.0
33.0
±200.0
±50.0
±83.0
±21.0
±67.0
±17.0
±42.0
±10.0
Efficiency
(%, Typ)
67
70
72
73
70
75
75
71
67
77
80
78
75
80
79
76
70
77
80
80
78
80
80
78
71
74
78
78
74
79
80
75
Capacitive
Load
(µF, Max)
3,300
3,300
470
470
±1,000
±220
±220
±100
3,300
3,300
470
470
±1,000
±220
±220
±100
3,300
3,300
470
470
±1,000
±220
±220
±100
3,300
3,300
470
470
±1,000
±220
±220
±100
Mechanical Dimensions
Fuse Rating
Slow-Blow
(mA)
1,500
1,500
1,500
1,500
1,500
1,500
1,500
1,500
700
700
700
700
700
700
700
700
350
350
350
350
350
350
350
350
135
135
135
135
135
135
135
135
Notes:
1. An external capacitor should be placed from the +Vout pin to the -Vout pin for
single output units and from each output to common for dual output units. For
single output units a 100 µF is recommended, for dual output models ±48 µF
should be used.
2. The Remote On/Off Control input (Pin 3) is referenced to -Vin (Pin 1). Connection
to the pin should be made through a 1kΩ resistor and diode (1N4148). If it is
not used, the control pin should be left open or tied directly to -Vin (Pin 1).
3. Operation at no-load will not damage these units. However, they may not
meet all specifications.
4. Dual output units may be connected to provide a 10 VDC, 24 VDC, 30 VDC or
48 VDC output. To do this, connect the load across the positive (+Vout) and
negative (-Vout) outputs and float the output common.
5. It is recommended that a fuse be used on the input of a power supply for
protection. See the table above for the correct rating.
Derating Curve
A metal case is available
Contact the factory for details at:
[e-mail]
Mechanical Notes:
• All dimensions are typical in inches (mm)
• Tolerance x.xx = ±0.01 (±0.25)
MicroPower Direct
Pin Connections
Pin Single Dual
1
-Vin
-Vin
2
+Vin
+Vin
3
Remote ON/OFF
5
NC
NC
6
+Vout +Vout
7
-Vout Common
8
NC
-Vout
NC = No Connection
www.micropowerdirect.com
292 Page Street Ste D Stoughton, MA 02072 • TEL: [phone] • FAX: [phone] • E-Mail: [e-mail]