D200E Datasheet, PDF (2/2 Pages) MicroPower Direct, LLC – Low Cost, 2W SIP Single & Dual Output DC/DC Converters

Model Selection Guide
Model
Number
D201E
D202E
D203E
D204E
D205E
D206E
D207E
D208E
D211E
D212E
D213E
D214E
D215E
D216E
D217E
D218E
D221E
D222E
D223E
D224E
D225E
D226E
D227E
D228E
Input
Voltage (VDC)
Current (mA)
Nominal Range Full-Load No-Load
5
4.5 - 5.5
494
30
5
4.5 - 5.5
488
30
5
4.5 - 5.5
476
30
5
4.5 - 5.5
476
30
5
4.5 - 5.5
488
30
5
4.5 - 5.5
482
30
5
4.5 - 5.5
470
30
5
4.5 - 5.5
470
30
12 10.8 - 13.2 203
15
12 10.8 - 13.2 201
15
12 10.8 - 13.2 196
15
12 10.8 - 13.2 196
15
12 10.8 - 13.2 201
15
12 10.8 - 13.2 198
15
12 10.8 - 13.2 194
15
12 10.8 - 13.2 194
15
24 21.6 - 26.4 100
8
24 21.6 - 26.4 99
8
24 21.6 - 26.4 97
8
24 21.6 - 26.4 97
8
24 21.6 - 26.4 99
8
24 21.6 - 26.4 98
8
24 21.6 - 26.4 96
8
24 21.6 - 26.4 96
8
Voltage
(VDC)
5.0
9.0
12.0
15.0
±5.0
±9.0
±12.0
±15.0
5.0
9.0
12.0
15.0
±5.0
±9.0
±12.0
±15.0
5.0
9.0
12.0
15.0
±5.0
±9.0
±12.0
±15.0
Output
Current
(mA, Max)
400.0
222.0
167.0
133.0
±200.0
±111.0
±83.0
±67.0
400.0
222.0
167.0
133.0
±200.0
±111.0
±83.0
±67.0
400.0
222.0
167.0
133.0
±200.0
±111.0
±83.0
±67.0
Current
(mA, Min)
40.0
23.0
17.0
14.0
±20.0
±12.0
±9.0
±7.0
40.0
23.0
17.0
14.0
±20.0
±12.0
±9.0
±7.0
40.0
23.0
17.0
14.0
±20.0
±12.0
±9.0
±7.0
Load
Regulation
(%, Max)
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
Efficiency
(%, Typ)
81
82
84
84
82
83
85
85
82
83
85
85
83
84
86
86
83
84
86
86
84
85
87
87
Fuse Rating
Slow-Blow
(mA)
1,000
1,000
1,000
1,000
1,000
1,000
1,000
1,000
500
500
500
500
500
500
500
500
200
200
200
200
200
200
200
200
Notes:
1. Output load regulation is specified for a load change of 10% to
100%.
2. These units should not be operated with a load under 10% of
full load. Operation at no-load may cause damage to the unit.
3. These converters will operate without external components.
However, when measuring output ripple, it is recommended
that an external ceramic capacitor be placed from the +Vout
pin to the -Vout pin for single output units and from each out-
put to common for dual output units. An input capacitor will
enhance stability over temperature and input line variations.
Recommended capacitor values are given in the table below.
For applications requiring very low output noise levels, a simple
LC filter should be effective.
Vin
Input
Capacitor
Vout
Output Capacitor
Single Dual
5 VDC 4.7 µF 5 VDC 10.0 µF 4.7 µF
12 VDC 2.2 µF 9 VDC 4.7 µF 2.2 µF
24 VDC 1.0 µF 12 VDC 2.2 µF 1.0 µF
15 VDC 1.0 µF 0.47 µF
Derating Curve
Mechanical Dimensions
4. Dual output units may be connected to provide a 10V, 18V, 24V
or 30 VDC output. To do this, connect the load across the posi-
tive (+Vout) and negative (-Vout) outputs and float the output
common
5. It is recommended that a fuse be used on the input of a power
supply for protection. See the Model Selection table above for
the correct rating.
Pin Connections
Pin Single Dual
Pin
1 +Vin +Vin
5
2 -Vin -Vin
6
4 -Vout -Vout
Single
No Pin
+Vout
Dual
Common
+Vout
Notes:
• All dimensions are typical in inches (mm)
• Tolerance x.xx = ±0.01 (±0.25)
• Pin 1 is marked by a “dot” or indentation on the side of the unit
MicroPower Direct
www.micropowerdirect.com
292 Page Street Ste D Stoughton, MA 02072 • TEL: [phone] • FAX: [phone] • E-Mail: [e-mail]