A300ERU_14 Datasheet, PDF (2/2 Pages) MicroPower Direct, LLC – A300ERU SERIES

Model Selection Guide
www.micropowerdirect.com
Model
Number
A301ERU
A302ERU
A303ERU
A304ERU
A305ERU
A306ERU
A307ERU
A311ERU
A312ERU
A313ERU
A314ERU
A315ERU
A316ERU
A317ERU
Voltage (VDC)
Nominal Range
24
9.0 - 36.0
24
9.0 - 36.0
24
9.0 - 36.0
24
9.0 - 36.0
24
9.0 - 36.0
24
9.0 - 36.0
24
9.0 - 36.0
48 18.0 - 72.0
48 18.0 - 72.0
48 18.0 - 72.0
48 18.0 - 72.0
48 18.0 - 72.0
48 18.0 - 72.0
48 18.0 - 72.0
Input
Current (mA) Reflected
Ripple Voltage
Full-Load No-Load Current (VDC)
(mA, Typ)
169
16
10
3.3
164
16
10
5.0
157
16
10
12.0
157
16
10
15.0
164
16
10
±5.0
157
16
10
±12.0
157
16
10
±15.0
84
8
10
3.3
80
8
10
5.0
78
8
10
12.0
78
8
10
15.0
82
8
10
±5.0
78
8
10
±12.0
78
8
10
±15.0
Output
Current
(mA, Max)
909
600
250
200
±300
±125
±100
909
600
250
200
±300
±125
±100
Current
(mA, Min)
90.0
60.0
25.0
20.0
±30.0
±12.0
±10.0
90.0
60.0
25.0
20.0
±30.0
±12.0
±10.0
Efficiency
(%, Typ)
74
76
80
80
76
80
80
74
78
80
80
76
80
80
Fuse Rating
Slow-Blow
(mA)
750
750
750
750
750
750
750
500
500
500
500
500
500
500
For models with a metal case, add an
“M” to the model number (ie: A315ERUM)
Derating Curve
Notes:
1. Exceeding the input range by a significant margin may damage the units. For 24V input the input voltage
should not exceed 40V; for 48V models it should not exceed 80V.
2. Voltage accuracy for the negative output on Dual output models is typically ±3% with a max of ±5%.
3. Maximum ouput noise for dual output units is 150 mV P-P. When measuring output ripple, it is recom-
mended that an external 0.33 µF ceramic capacitor be placed from the +Vout pin to the -Vout pin for single
output units and from each output to common for dual output units.
4. The optional metal package is nickel plated steel. The dimensions of the metal package are 1.25 x 0.80 x 0.39
Inches (31.8 x 20.3 x 10.0 mm).
5. These units should not be operated with a load under the specified minimum. Operation at no-load will
increase ripple significantly and may cause damage to the unit.
6. These converters are specified for operation without external components. However, in some applications
the addition of input/output capacitors will enhance stability and reduce output ripple. Recommended
capacitor values are:
Vin: 10 µF - 47 µF
Vout: 10 µF/100 mA
For applications requiring very low output noise levels, a simple LC filter
should be effective.
Mechanical Dimensions
7. The maximum load capacitance is:
Maximum
Vout
Load
Capacitance
Vout
Maximum
Load
Capacitance
3.3 VDC
5 VDC
12 VDC
15 VDC
2,200 µF
1,000 µF
470 µF
330 µF
±5 VDC
±12 VDC
±15 VDC
2,200 µF
1,000 µF
470 µF
8. It is recommended that a fuse be used on the input of a power supply for
protection. See the Model Selection table above for the correct rating.
Pin Connections
Pin Single Dual
2, 3
-Vin
-Vin
9
NC Common
10
NC
NC
11
NC
-Vout
14
+Vout +Vout
15
NC
NC
16
-Vout Common
22, 23 +Vin
+Vin
NC: No Connection
MicroPower Direct
Mechanical Notes:
• All dimensions are typical in inches (mm)
• Tolerance x.xx = ±0.01 (±0.25)
We Power Your Success - For Less!
292 Page Street Ste D Stoughton, MA 02072 • TEL: [phone] • FAX: [phone] • E-Mail: [e-mail]