MPM-10IS_14 Datasheet, PDF (1/2 Pages) MicroPower Direct, LLC – MPM-10IS Series

MPM-10IS Series
Board Mount, 10W
Single & Dual Output
AC/DC Power Supplies
Key Features:
• 10W Output Power
• Universal 85-265 VAC Input
• EN 60950 Approved (UL)
• ErP Directive Compliant
• Meets IEC Safety Class II
• Industry Standard Pin-Out
• Meets EN 55022 B
• >300 kHour MTBF
MicroPower Direct
292 Page Street
Suite D
Stoughton, MA 02072
USA
T: [phone]
F: [phone]
E: [e-mail]
W: www.micropowerdirect.com
Electrical Specifications
Specifications typical @ +25°C, 230 VAC input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Input
Parameter
Conditions
Min. Typ. Max. Units
Input Voltage Range
85
265
VAC
Input Frequency
47
440
Hz
Input Current
See Model Selection Guide
Inrush Current
115 VAC
10.0
230 VAC
20.0
A Pk
EMI
Meets CISPR Pub. 22/FCC Class B
Output
Parameter
Conditions
Min. Typ. Max. Units
Output Voltage
See Model Selection Guide
Output Current
See Model Selection Guide
Output Voltage Accuracy
±1.0 ±2.0
%
Line Regulation
VIN = Min to Max
±0.5 ±1.0
%
Load Regulation, Single Output
IO = Min to Max
±0.5 ±1.0
%
Load Regulation, Dual Output
IO = Min to Max
±2.5 ±5.0
%
Ripple & Noise (20 MHz)
3.3V & 5.0 VDC Output
All Other Outputs
1.5 1.8
0.8
1.0 ^{%VP-P of VO}
Hold-Up Time
115 VAC, 60 Hz
20
mSec
Temperature Coefficient
±0.02
%/°C
Over Voltage Protection
Zener Diode Clamp
120
% of VO
Short Circuit Protection, See Note 3
Continuous (Autorecovery)
Overload Protection
See Note 4 105
% of INOM
General
Parameter
Conditions
Min. Typ. Max. Units
Isolation Voltage
Input to Output 3,000
VAC
Isolation Test Voltage
Input to Output, Flash Tested For 60S 4,700
VAC
Isolation Resistance
500 VDC 100
M
EMI/RFI
Conducted
EN 55022 Level B
Electrostatic Discharge (ESD)
EN 61000-4-2 Level 3
EMC Compliance
RF Field Susceptibility
Electrical Fast Transients/Bursts On Mains
EN 61000-4-3
EN 61000-4-4 Level 3 2 kV
Surge
EN 61000-4-5 Level 3 1kV/2 kV
Switching Frequency
100
kHz
Environmental
Parameter
Conditions
Min. Typ. Max. Units
Operating Temperature Range
Ambient -25 +25 +71
°C
Storage Temperature Range
-40
+85
°C
Cooling
Free Air Convection (See Derating Curve)
Humidity
RH, Non-condensing
95
%
Physical
Case Size
2.52 x 1.77 x 0.75 Inches (64.0 x 45.0 x 19.0 mm)
Case Material
Non-Conductive Plastic & Fiberglass (UL94-V0)
Weight
3.23 Oz (92g)
Reliability Specifications
Parameter
Conditions
Min. Typ. Max. Units
MTBF
MIL HDBK 217F, 25°C, Gnd Benign 300
kHours
Safety Standards
EN 60950
Safety Class
IEC 61140 Class II
ECO Design
ErP Directive 2009/125/EC
www.micropowerdirect.com