MPL-01SE Datasheet, PDF (1/2 Pages) MicroPower Direct, LLC – Single Output, 1W Ultra-Miniature SIP AC/DC Power Supplies

MPL-01SE Series
Single Output, 1W
Ultra-Miniature SIP
AC/DC Power Supplies
Key Features:
Electrical Specifications
• 1W Output Power
• Universal 85-264 VAC Input
• EN 60950 Approved (UL)
• Meets IEC Safety Class II
Specifications typical @ +25°C, 230 VAC input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Input
Parameter
Conditions
Min. Typ. Max. Units
Input Voltage Range
85
264
VAC
100
400
VDC
• Single Regulated Output
• Meets EN 55022 Class A
• >300 kHour MTBF
• Ultra-Miniature “SIP” Case
Input Frequency
Input Current
Inrush Current
Standby Power
47
63
See Model Selection Guide
115 VAC
10.0
230 VAC
20.0
0.3
Hz
A Pk
W
Output
Parameter
Conditions
Min. Typ. Max. Units
Output Voltage
See Model Selection Guide
Output Current
See Model Selection Guide
Output Voltage Accuracy, See Note 1
See Model Selection Guide
Line Regulation
VIN = Min to Max
±1.5
%
Load Regulation
IOUT = 5% to 100%
±2.5
%
Ripple & Noise (20 MHz)
5V, 24V Models
9V, 12V, 15V Models
100 150
80 120
mV P-P
Hold-Up Time
230 VAC
50
mSec
Temperature Coefficient
±0.01
%/°C
Short Circuit Protection
Continuous (Autorecovery)
Over Temperature Protection
150
°C
General
Parameter
Conditions
Min. Typ. Max. Units
Isolation Voltage
Input to Output 3,000
VAC
Switching Frequency
50
kHz
EMI Characteristics
Parameter
Standard
Min. Typ. Max. Units
Radiated Emissions
See Note 3
EN 55022
Class A
Conducted Emissions
See Note 3
EN 55022
Class A
ESD
EN 61000-4-2
Criteria B; ±4 kV Contact
RS
See Note 4 EN 61000-4-3
Criteria A; 10V/m
EFT
See Note 5 EN 61000-4-4
Criteria B; ±2 kV
Surge
See Note 6 EN 61000-4-5
Criteria B; ±1 kV /±2 kV
CS
See Note 7 EN 61000-4-6
Criteria A; 3 Vrms
PFMF
EN 61000-4-8
Criteria A; 10A/m
Voltage Dips
EN 61000-4-11
Criteria B; 0% - 70%
Environmental
MicroPower Direct
292 Page Street
Suite D
Stoughton, MA 02072
USA
Parameter
Operating Temperature Range
Operating Temperature Range
Storage Temperature Range
Cooling
Humidity
Conditions
Min. Typ. Max.
Ambient -40 +25 +85
Case
+90
-40
+105
Free Air Convection (See Derating Curve)
RH, Non-condensing
85
Units
°C
°C
°C
%
T: [phone]
F: [phone]
E: [e-mail]
W: www.micropowerdirect.com
Physical
Case Size
Case Material
Weight
Reliability Specifications
1.38 x 0.43 x 0.94 Inches (35.0 x 11.0 x 24.0 mm)
Non-Conductive Epoxy (UL94-V0)
0.35 Oz (10g)
Parameter
Conditions
Min. Typ. Max. Units
MTBF
MIL HDBK 217F, 25°C, Gnd Benign 300
kHours
Safety Standards
EN 60950
Safety Class
IEC 61140 Class II
www.micropowerdirect.com