|
ML200SEI Datasheet, PDF (1/2 Pages) MicroPower Direct, LLC – 2W, High Isolation Ultra-Miniature SMT DC/DC Converters | |||
|
ML200SEI Series
2W, High Isolation
Ultra-Miniature SMT
DC/DC Converters
Electrical Speciï¬cations
Speciï¬cations typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Speciï¬cations subject to change without notice.
Key Features:
⢠2W Output Power
⢠Ultra-Miniature SMT Case
⢠3,000 VDC Isolation
Input
Parameter
Input Voltage Range
Conditions
Min. Typ. Max.
5 VDC Input 4.5 5.0 5.5
12 VDC Input 10.8 12.0 13.2
15 VDC Input 13.5 15.0 16.5
Units
VDC
⢠Single Output
24 VDC Input 21.6 24.0 26.4
⢠-40°C to +105°C Operation Input Filter
Capacitor
⢠>3.5 MHour MTBF
Output
⢠13 Standard Models
⢠LOW COST!
Parameter
Output Voltage Accuracy
Capacitive Load
Conditions
Min. Typ. Max.
±3.0
220
Units
%
µF
Line Regulation
For Vin Change of 1%
±1.2
%
Load Regulation, See Note 1
See Model Selection Guide
Ripple & Noise (20 MHz)
See Note 2
100 200 mV P - P
Temperature Coefï¬cient
±0.03 %/ºC
Output Short Circuit
Momentary (1S Max)
General
Parameter
Conditions
Min. Typ. Max. Units
Isolation Voltage
60 Seconds 3,000
VDC
Isolation Resistance
500 VDC 1,000
Mâ
Isolation Capacitance
100 kHz, 0.1V
20
pF
Switching Frequency
100
kHz
EMI Characteristics
Parameter
Standard
Criteria
Level
Radiated Emissions
EN 55022
B
Conducted Emissions
EN 55022
B
ESD
EN 61000-4-2
B
±8kV
Environmental
Parameter
Conditions
Min. Typ. Max. Units
Operating Temperature Range
Ambient -40 +25 +105
ºC
Storage Temperature Range
-55
+125
ºC
Cooling
Free Air Convection
Humidity
RH, Non-condensing
95
%
Physical
Case Size
See Mechanical Drawing (Page 2)
Case Material
Non-Conductive Black Plastic (UL94-V0)
MicroPower Direct
292 Page Street
Suite D
Stoughton, MA 02072
USA
Weight
Reliability Speciï¬cations
Parameter
MTBF
Absolute Maximum Ratings
0.05 Oz (1.52g)
Conditions
Min. Typ. Max.
MIL HDBK 217F, 25ºC, Gnd Benign 3.5
Units
MHours
T: (781) 344-8226
F: (781) 344-8481
E: sales@micropowerdirect.com
W: www.micropowerdirect.com
Parameter
Input Voltage Surge (1 Sec)
Conditions
Min. Typ. Max.
5 VDC Input -0.7
9.0
12 VDC Input -0.7
18.0
15 VDC Input -0.7
21.0
Units
VDC
24 VDC Input -0.7
30.0
Peak Reï¬ow Temperature
See Note 5
245
ºC
Lead Temperature
1.5 mm From Case For 10 Sec
300
ºC
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
www.micropowerdirect.com
|
▷ |