ML100SE Datasheet, PDF (1/2 Pages) MicroPower Direct, LLC – ML100SE SERIES

ML100SE Series
Low Cost, Single Output
Ultra-Miniature SMT
DC/DC Converters
Electrical Specifications
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Key Features:
• 1W Output Power
• Ultra-Miniature SMT Case
• 1,500 VDC Isolation
• Short Circuit Protected
• Single Output
• -40°C to +105°C Operation
• >3.5 MHour MTBF
Input
Parameter
Input Voltage Range
Input Filter
Output
Parameter
Conditions
Min. Typ. Max.
5 VDC Input 4.5 5.0 5.5
12 VDC Input 10.8 12.0 13.2
15 VDC Input 13.5 15.0 16.5
24 VDC Input 21.6 24.0 26.4
Capacitor
Conditions
Min. Typ. Max.
Units
VDC
Units
• 17 Standard Models
Output Voltage Accuracy
±3.0
%
• LOW COST!
Capacitive Load
220
µF
Line Regulation
For Vin Change of 1%
±1.2
%
Load Regulation, See Note 1
See Model Selection Guide
Ripple & Noise (20 MHz), See Note 2
Output Voltage <12 VDC
30
15 VDC, 24 VDC Output
60
mV P - P
Temperature Coefficient
±0.03 %/ºC
Output Short Circuit
Continuous (Autorecovery)
General
Parameter
Conditions
Min. Typ. Max. Units
Isolation Voltage
60 Seconds 1,500
VDC
Isolation Resistance
500 VDC 1,000
M⍀
Isolation Capacitance, See Note 3
100 kHz, 1V
20
pF
Switching Frequency
100 300
kHz
EMI Characteristics
Parameter
Conditions
Min. Typ. Max. Units
EMI Compliance, See Note 5
Conducted
CISPR22/EN 55022 Level B
EMC Compliance
Electrostatic Discharge (ESD) EN 61000-4-2 Level B Contact ±8 kV
Environmental
Parameter
Conditions
Min. Typ. Max. Units
Operating Temperature Range
Ambient -40 +25 +105
ºC
Storage Temperature Range
-55
+125
ºC
Cooling
Free Air Convection
Humidity
RH, Non-condensing
95
%
Physical
Case Size
0.50 x 0.327 x 0.285 Inches (12.70 x 8.30 x 7.25 mm)
MicroPower Direct
292 Page Street
Suite D
Stoughton, MA 02072
USA
Case Material
Weight
Reliability Specifications
Parameter
MTBF
Non-Conductive Black Plastic (UL94-V0)
0.05 Oz (1.52g)
Conditions
Min. Typ. Max.
MIL HDBK 217F, 25ºC, Gnd Benign 3.5
Units
MHours
T: [phone]
F: [phone]
E: [e-mail]
W: www.micropowerdirect.com
Absolute Maximum Ratings
Parameter
Input Voltage Surge (1 Sec)
Conditions
Min. Typ. Max.
5 VDC Input -0.7
9.0
12 VDC Input -0.7
18.0
15 VDC Input -0.7
21.0
Units
VDC
24 VDC Input -0.7
30.0
Lead Temperature
1.5 mm From Case For 10 Sec
300.0
ºC
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
www.micropowerdirect.com