MHI600ARWI8 Datasheet, PDF (1/2 Pages) MicroPower Direct, LLC – Wide Input, 6W DIP Ultra-High Isolation DC/DC Converters

MHI600ARWI8_Series
Wide Input, 6W DIP
Ultra-High Isolation
DC/DC Converters
Electrical Specifications
Key Features:
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Input
• 6W Output Power
Parameter
Conditions
Min. Typ. Max. Units
• 8.0 kV Isolation
• 15 kV/µS CMTI
Input Voltage Range
12 VDC Input 9.0 12.0 18.0
24 VDC Input 18.0 24.0 36.0
48 VDC Input 36.0 48.0 75.0
VDC
• Wide 2:1 Input Range
• Reinforced Insulation
Start-Up Threshold Voltage
12 VDC Input 7.0 8.0 9.0
24 VDC Input 13.0 15.0 18.0
48 VDC Input 30.0 33.0 36.0
VDC
• EN 60950 Approved (Pend.)
Under Voltage Shutdown
• -40°C to +75°C Operation
12 VDC Input
24 VDC Input
48 VDC Input
8.5
16.0
VDC
34.0
• Industry Standard Pin-Out ^{Short Circuit Input Power}
Input Filter
␲ (Pi) Filter
3,000
mW
Conducted EMI
Meets EN 55022 Class A & FCC Level A
Output
Parameter
Conditions
Min. Typ. Max. Units
Output Voltage Accuracy
±1.0
%
Output Voltage Balance
Dual Output, Balanced Loads
±0.5 ±2.0
%
Line Regulation
VIN = Min to Max
±0.3 ±0.5
%
Load Regulation
See Note 2
±0.5 ±1.0
%
Ripple & Noise (20 MHz)< See Note 3
5 VDC Output Models
All Other Models
75
100
100
150
mV P - P
Transient Recovery Time, See Note 4
Transient Response Deviation
25% Load Step Change
300 500
±3.0 ±6.0
µSec
%
Output Power Protection
Foldback 120 150
%
Temperature Coefficient
±0.02 ±0.05 %/°C
Output Short Circuit
Continuous (Autorecovery)
General
Parameter
Conditions
Min. Typ. Max. Units
Isolation Voltage, 60 Sec
Rated For 60 Sec 4,000
Tested For 1 Sec 8,000
VAC rms
VDC
Isolation Resistance
500 VDC 10
G
Isolation Capacitance
100 kHz, 1V
7
13
pF
Common Mode Transient Immunity
15
kV/µS
Switching Frequency
Environmental
150
kHz
Parameter
Conditions
Min. Typ. Max. Units
Operating Temperature Range
Ambient -40 +25 +75
Case
+95
°C
Storage Temperature Range
-50
+125
°C
Cooling
Free Air Convection
MicroPower Direct
Humidity
Physical
RH, Non-condensing
95
%
292 Page Street
Case Size
See Mechanical Diagram (Page 3)
Suite D
Stoughton, MA 02072
USA
Case Material
Weight
Reliability Specifications
Parameter
Conditions
Non-Conductive Black Plastic (UL94-V0)
0.57 Oz (16.2g)
Min. Typ. Max. Units
T: [phone]
F: [phone]
E: [e-mail]
W: www.micropowerdirect.com
MTBF
Safety Standards
Absolute Maximum Ratings
Parameter
MIL HDBK 217F, 25°C, Gnd Benign 700
UL 60950, EN 60950 (Pending)
Conditions
Min. Typ. Max.
12 VDC Input
25.0
kHours
Units
Input Voltage Surge (0.1 Sec)
24 VDC Input
50.0
VDC
48 VDC Input
100.0
Lead Temperature
1.5 mm From Case for 10 Sec
260
°C
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
www.micropowerdirect.com