MH100SE Datasheet, PDF (1/2 Pages) MicroPower Direct, LLC – MH100SE SERIES

MH100SE Series
Low Cost, 1W
Ultra-Miniature
DC/DC Converters
Key Features:
• 1W Output Power
• Ultra-Miniature Case
Electrical Specifications
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Input
Parameter
Conditions
Min. Typ. Max. Units
3.3 VDC Input 2.97 3.3 3.63
5 VDC Input 4.50 5.0 5.50
• Short Circuit Protected
• 1,500 VDC Isolation
• >3.5 MHour MTBF
• -40°C to +105°C Operation
Input Voltage Range
Input Filter
Output
12 VDC Input 10.80 12.0
15 VDC Input 13.50 15.0
24 VDC Input 21.60 24.0
Internal Capacitor
13.20
16.50
26.40
VDC
• LOW COST
Parameter
Output Voltage Accuracy
Conditions
Min. Typ. Max.
±3.0
Units
%
Capacitive Load
220
µF
Line Regulation
For Vin Change of 1%
±1.2
%
Load Regulation, See Note 1
See Model Selection Guide
Ripple & Noise (20 MHz), See Note 2
Output Voltage <12 VDC
30
15 VDC, 24 VDC Output
60
mV P - P
Temperature Coefficient
±0.03 %/°C
Output Short Circuit
Continuous (Autorecovery)
General
Parameter
Conditions
Min. Typ. Max. Units
Isolation Voltage
60 Seconds 1,500
VDC
Isolation Resistance
500 VDC 1,000
M
Isolation Capacitance, See Note 3
100 kHz, 1V
20
pF
Switching Frequency
100 300
kHz
EMI Characteristics
Parameter
Conditions
Min. Typ. Max. Units
EMI Compliance, See Note 5
Conducted
CISPR22/EN 55022 Level B
EMC Compliance
Electrostatic Discharge (ESD) EN 61000-4-2 Level B Contact ±8 kV
Environmental
Parameter
Conditions
Min. Typ. Max. Units
Operating Temperature Range
Ambient -40
+105
°C
Storage Temperature Range
-55
+125
°C
Cooling
Free Air Convection
Humidity
RH, Non-condensing
95
%
Physical
Case Size
0.50 x 0.394 x 0.323 Inches (12.7 x 10.0 x 8.2 mm)
MicroPower Direct
292 Page Street
Suite D
Stoughton, MA 02072
USA
Case Material
Weight
Reliability Specifications
Parameter
MTBF
Non-Conductive Black Plastic (UL-94V0)
0.06 Oz (1.8g)
Conditions
Min. Typ. Max.
MIL HDBK 217F, 25°C, Gnd Benign 3.5
Units
MHours
T: [phone]
F: [phone]
E: [e-mail]
W: www.micropowerdirect.com
Absolute Maximum Ratings
Parameter
Input Voltage Surge (1 Sec)
Conditions
Min. Typ. Max.
3.3 VDC Input -0.7
5.0
5 VDC Input -0.7
9.0
12 VDC Input -0.7
18.0
Units
VDC
12 VDC Input -0.7
21.0
24 VDC Input -0.7
30.0
Lead Temperature
1.5 mm From Case For 10 Sec
300
°C
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
www.micropowerdirect.com