MG200EI Datasheet, PDF (1/2 Pages) MicroPower Direct, LLC – MG200xEI SERIES

MG200xEI Series
High Isolation, 2W
Compact MiniDIP
DC/DC Converters
Key Features:
• 2W Output Power
• Compact MiniDIP Case
• 3,000 VDC Isolation
• High Efficiency
• Single and Dual Outputs
Electrical Specifications
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Input
Parameter
Conditions
Min. Typ. Max. Units
5 VDC Input 4.50 5.0 5.50
Input Voltage Range
12 VDC Input 10.80 12.0 13.20
15 VDC Input 13.50 15.0 16.50
VDC
24 VDC Input 21.60 24.0 26.40
Input Filter
Internal Capacitor
Output
• >3.5 MHour MTBF
Parameter
Conditions
Min. Typ. Max. Units
• -40°C to +85°C Operation
• LOW COST
Output Voltage Accuracy
Line Regulation
Load Regulation, See Note 1
±2.5
%
For VIN Change of 1%
±1.2
%
See Model Selection Guide
1.5 kV Isolation
Models
Available
Ripple & Noise (20 MHz), See Note 2
Temperature Coefficient
Output Short Circuit
Output Voltage <12 VDC
15 VDC, 24 VDC Output
5 VDC, 12 VDC & 15 VDC Input
24 VDC Input
60
mV P - P
75
±0.03 %/°C
Continuous (Autorecovery)
Momentary (1.0 Sec.)
General
Parameter
Conditions
Min. Typ. Max. Units
Isolation Voltage
60 Seconds 3,000
VDC
Isolation Resistance
500 VDC 1,000
M
Isolation Capacitance
100 kHz, 0.1V
20
pF
Switching Frequency
100 300
kHz
EMI Characteristics
Parameter
Conditions
Min. Typ. Max. Units
EMI Compliance, See Note 4
Conducted
Radiated
CISPR22/EN 55022 Level B
CISPR22/EN 55022 Level B
EMC Compliance, Single Output
EMC Compliance, Dual Output
EN 61000-4-2 Level B Contact ±8 kV
Electrostatic Discharge (ESD)
EN 61000-4-2 Level B Contact ±6 kV
Environmental
Parameter
Conditions
Min. Typ. Max. Units
Operating Temperature Range
Ambient -40 +25 +85
°C
Storage Temperature Range
-55
+125
°C
Cooling
Free Air Convection
Humidity
RH, Non-condensing
95
%
Physical
Case Size
0.787 x 0.394 x 0.323 Inches (20.0 x 10.0 x 8.2 mm)
MicroPower Direct
292 Page Street
Suite D
Stoughton, MA 02072
USA
Case Material
Weight
Reliability Specifications
Parameter
MTBF
Non-Conductive Black Plastic (UL-94V0)
0.08 Oz (2.4g)
Conditions
Min. Typ. Max.
MIL HDBK 217F, 25°C, Gnd Benign 3.5
Units
MHours
T: [phone]
F: [phone]
E: [e-mail]
W: www.micropowerdirect.com
Absolute Maximum Ratings
Parameter
Input Voltage Surge (1 Sec)
Conditions
Min. Typ. Max.
5 VDC Input -0.7
9.0
12 VDC Input -0.7
18.0
15 VDC Input -0.7
21.0
Units
VDC
24 VDC Input -0.7
30.0
Lead Temperature
1.5 mm From Case For 10 Sec
300
°C
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
www.micropowerdirect.com