|
LF200S_14 Datasheet, PDF (1/2 Pages) MicroPower Direct, LLC – LF200S SERIES | |||
|
LF200S Series
Ultra-Miniature, 2W
Single Output SMT
DC/DC Converters
Key Features:
Electrical Speciï¬cations
Speciï¬cations typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Speciï¬cations subject to change without notice.
Input
Parameter
Conditions
Min. Typ. Max. Units
⢠2W Output Power
5 VDC Input 4.5 5.0 5.5
⢠Ultra-Miniature SMT Case Input Voltage Range
12 VDC Input 10.8 12.0 13.2
VDC
⢠1,000 VDC Isolation
24 VDC Input 21.6 24.0 26.4
⢠5V, 12 & 24V Inputs
⢠-40ºC to +85ºC Operation
⢠6 Standard Models
⢠2.0 MH MTBF Minimum
⢠Industry Standard Pin-Out
Reverse Polarity Input Current
Input Filter
Output
Parameter
Output Voltage Accuracy
Line Regulation
0.3
Capacitor
Conditions
Min. Typ. Max.
±1.5 ±4.0
For Vin Change of 1%
±1.2 ±1.5
A
Units
%
%
Load Regulation, See Note 1
See Model Selection Guide
Ripple & Noise (20 MHz)
See Note 2
50 75 mV P - P
Ripple & Noise (20 MHz)
Over Line, Load & Temp.
150 mV P - P
Ripple & Noise (20 MHz)
5
mv rms
Output Power Protection
120
%
Temperature Coefï¬cient
±0.01 ±0.02 %/ºC
Output Short Circuit
Momentary (0.5 Sec.)
General
Parameter
Conditions
Min. Typ. Max. Units
Isolation Voltage
60 Seconds 1,000
VDC
Isolation Resistance
500 VDC 10
Gï
Isolation Capacitance
100 kHz, 1V
60 100
pF
Switching Frequency
70 100 120
kHz
Environmental
Parameter
Conditions
Min. Typ. Max. Units
Operating Temperature Range
Ambient -40 +25 +85
ºC
Operating Temperature Range
Case -40
+90
ºC
Storage Temperature Range
-40
+125
ºC
Cooling
Free Air Convection
Humidity
RH, Non-condensing
95
%
Physical
Case Size
0.50 x 0.36 x 0.34 Inches (12.7 x 9.3 x 8.7 mm)
MicroPower Direct
292 Page Street
Suite D
Stoughton, MA 02072
USA
Case Material
Weight
Reliability Speciï¬cations
Parameter
MTBF
Molding (UL94-V0)
0.05 Oz (1.5g)
Conditions
Min. Typ. Max.
MIL HDBK 217F, 25ºC, Gnd Benign 2.0
Units
MHours
T: (781) 344-8226
F: (781) 344-8481
E: sales@micropowerdirect.com
W: www.micropowerdirect.com
Absolute Maximum Ratings
Parameter
Input Voltage Surge (1 Sec)
Conditions
Min. Typ. Max. Units
5 VDC Input -0.7
9.0
12 VDC Input -0.7
18.0
VDC
24 VDC Input -0.7
30.0
Lead Temperature
1.5 mm From Case For 10 Sec.
300
ºC
Internal Power Dissipation
All Models
650
mW
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
www.micropowerdirect.com
|
▷ |