|
LDF24E Datasheet, PDF (1/2 Pages) MicroPower Direct, LLC – LDF24E-XX-XXX SERIES | |||
|
LDF24E-xx-xxx Series
Miniature, SMT
Constant Current Output
DC/DC LED Drivers
Electrical Speciï¬cations
Speciï¬cations typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Speciï¬cations subject to change without notice.
Key Features:
Input
Parameter
⢠300 - 700 mA Output Current Input Voltage Range
Conditions
Min. Typ. Max.
5.5 24.0 48.0
Units
VDC
⢠Constant Current Output
⢠Miniature SMTCase
Max Input Voltage
Input Filter
Output
See Note 1
Internal Capacitor
55.0
VDC
⢠PWM & Analog Dimming Parameter
Output Current Accuracy
⢠Wide 5.5V to 48V Input Range Output Current Stability
Conditions
Min. Typ. Max.
Vin = 24V
±2.0 ±3.0
Vin = 48V
±1.0
Units
%
%
⢠Efï¬ciency to 96%
⢠2.0 MHrs MTBF
Output Capacitive Load
Ripple & Noise
Temperature Coefï¬cient
1,000
120
±0.015
µF
mV P-P
%/ºC
⢠Low, Low Cost!
Output Short Circuit
Continuous
Environmental
Parameter
Conditions
Min. Typ. Max. Units
Operating Temperature Range, Ambient
300 mA, 350 mA Output Models -40 +25 +85
All Other Models -40 +25 +71
ºC
Operating Temperature Range, Case
Case
+100
ºC
Storage Temperature Range
-55
+125
ºC
Cooling
Free Air Convection
Humidity
RH, Non-condensing
95
%
Lead Temperature
1.5 mm From Case For 10 Sec
260
ºC
Physical
Case Size
0.94 x 0.54 x 0.295 Inches (23.86 x 13.70 x 7.50 mm)
Case Material
Non-Conductive Black Plastic (UL94-V0)
Weight
0.212 Oz (6.0g)
Remote On/Off Control
Parameter
Conditions
Min. Typ. Max. Units
DC/DC On
Open Or 2.8 VDC < 6.0 VDC
DC/DC Off
<0.6 VDC
Remote Pin Drive Current
Vcont = 5.0 VDC
1
mA
Quiescent Input Current (Shutdown Mode)
Vin = 24V, Vcont = <0.6 VDC
400
µA
PWM Dimming
Parameter
Conditions
Min. Typ. Max. Units
Operation Frequency
0.2
10
kHz
Reliability Speciï¬cations
Parameter
Conditions
Min. Typ. Max. Units
MTBF
MIL HDBK 217F, 25ºC, Gnd Benign 2.0
MHours
Typical Connection: DC Input
Connection Notes:
1. Input ï¬lter components (C1, L1 & C2) are
used to help meet the conducted emissions
MicroPower Direct
292 Page Street
Suite D
Stoughton, MA 02072
USA
requirements (EN 55022 B) for the unit.
Recommended values are:
C2 - 2.2 µF
L1 - 1.25 mH
C3 - 1.0 µF
Other components added to the circuit
include an input storage capacitor to help
T: (781) 344-8226
F: (781) 344-8481
Typical Connection: AC Input
E: sales@micropowerdirect.com
W: www.micropowerdirect.com
prevent problems due to input line sags and
an output capacitor to improve performance.
Recommended values are:
C1 - 470 µF
C4 - 1.0 µF
2. To comply with EN61000-4-5, a TVS should
be installed before the input ï¬lter compo-
nents. A SMCG51 is recommended.
www.micropowerdirect.com
|
▷ |