IGD1208W Datasheet, PDF (1/2 Pages) MicroPower Direct, LLC – Internal DC/DC Converter

IGD1208W
Hybrid Integrated
Isolated N-Channel
IGBT Driver
Electrical Specifications
Key Features:
Absolute Maximum Ratings, TA = 25 ºC, VD = 12V or 15V, RG = 5⍀, unless otherwise noted.
• Internal DC/DC Converter ^Parameter
Conditions
Min. Typ. Max.
• Internal OptoCoupler
Supply Voltage
VD
16
• 30 kV/µS CMR
Input Current
IIN
See Note 4
25
• VISO = 3,750V
Output Voltage
VO
When Output is “H”
VCC
• TTL Compatible Input
• Short Circuit Protected Output Current
IGON
Pulse Width 2 µS, Frequency Ϲ 20 kHz
+8.0
• Fault Signal Output
IGOFF
-8.0
• Switching Freq. to 20 kHz ^{Isolation Voltage}
VISO Sine Wave Voltage 50 Hz/ 60 Hz , 1 Min
3,750
• Compact SIP Package
Operating Temperature
TOP
-40
+70
Storage Temperature
TST
-50
+125
Fault Output Current
IFO
See Note 5
20
Recommended For: ^{Input Voltage To Detection Pin VR1}
See Note 3
50
• 600V Series IGBT (up to 600A) Electrical Characteristics, TA = 25 ºC, VCC = 15 VDC, VEE = -10 VDC unless otherwise noted.
• 1200V Series IGBT (up to 400A) _Parameter
Conditions
Min. Typ. Max.
• 1700V Series IGBT (up to 200A) _{Supply Voltage}
VD
Recommended Range 14.5 15 15.5
Switching Frequency
f
Recommended Range 0
20
Gate Resistor
RG
2
VCC
Gate Supply Voltage
VEE
VD = 15V 14.5
VD = 15V -7.0
18.0
-10.0
Input CMR
15 30
“H” Input Current
IIH
Recommended Range 10 16 20
“H” Output Voltage
VOH 10 k⍀ Connected Between Pins 9 - 11 13.5 15.3 17.0
“L” Output Voltage
VOL 10 k⍀ Connected Between Pins 9 - 11 -6
-10
“L-H” Propagation
TPLH
IIH = 10 mA
0.5 1.0
“L-H” Rise Time
TR
IIH = 10 mA
0.3 1.0
“H-L” Propagation
TPHL
IIH = 10 mA
1.0 1.3
“H-L” Fall Time
TF
IIH = 10 mA
0.3 1.0
Protection Threshold Voltage VOCP
VD = 15V
9.5
Protection Reset Time
TTIMER
Between Start & Cancel 1.0 1.4 2.0
MicroPower Direct
292 Page Street
Suite D
Stoughton, MA 02072
USA
Fault Output Current
Controlled Time Detect
Soft Turn-Off Time
SC Detect Voltage
IFO
TTRIP1
TCF
VSC
See Note 6
5.0
See Note 7
3.0
See Note 8
4.5
Collector Voltage of Module 15
T: [phone]
F: [phone]
E: [e-mail]
W: www.micropowerdirect.com
Notes:
1. Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
2. ”H” = high level signal. “L” = low level signal.
3. The voltage applied to pin 13.
4. The current measured between pins 3 and 4.
5. The current at pin 15.
6. The current at pin 15. RF (on connection diagram) = 4.7 k⍀.
7. Pin 13 м 15 VDC. Pin 16 open.
8. Pin 13 м 15 VDC. Pin 14 open.
www.micropowerdirect.com
Units
VDC
mA
VDC
A
VAC
ºC
ºC
mA
VDC
Units
VDC
kHz
⍀
VDC
kV/µS
mA
VDC
VDC
µS
µS
µS
µS
V
mS
mA
µS
µS
VDC