IGD1205W Datasheet, PDF (1/2 Pages) MicroPower Direct, LLC – Hybrid Integrated Isolated N-Channel IGBT Driver

IGD1205W
Hybrid Integrated
Isolated N-Channel
IGBT Driver
Electrical Specifications
Key Features:
• Internal DC/DC Converter
• Internal OptoCoupler
• 30 kV/µS CMR
• VISO = 3,750V
• TTL Compatible Input
• Short Circuit Protected
• Fault Signal Output
• Switching Freq. to 20 kHz
• Compact SIP Package
Absolute Maximum Ratings, TA = 25 ºC, VD = 12V or 15V, RG = 5⍀, unless otherwise noted.
Parameter
Conditions
Min. Typ.
VD
Supply Voltage
VD
IGD1205W-12
IGD1205W-15
Input Voltage
VIN
See Note 3
Input Current
IIN
See Note 4
Output Voltage
VO
When Output is “H”
Output Current
IGON
Pulse Width 2µS, Frequency Ϲ 20 kHz
IGOFF
Isolation Voltage
VISO Sine Wave Voltage 50 Hz/ 60 Hz , 1 Min
Operating Temperature
TOP
-40
Storage Temperature
TST
Recommended For: _{Fault Output Current}
IFO
-50
See Note 5
• 600V Series IGBT (up to 600A) _{Electrical Characteristics, TA = 25 ºC, VCC = 15 VDC, VEE = -10 VDC unless otherwise noted.}
• 1200V Series IGBT (up to 400A)
• 1700V Series IGBT (up to 200A) ^Parameter
Conditions
Min. Typ.
VD IGD1205W-12 Recommended Range 11.6 12
Supply Voltage
VD IGD1205W-15 Recommended Range 14.5 15
Switching Frequency
f
Recommended Range 0
Gate Resistor
RG
2
VCC
Gate Supply Voltage
VEE
14.5
-7.0
Input CMR
15 30
“H” Input Current
IIH
Recommended Range 10 16
“H” Output Voltage
VOH
13.5 15.3
“L” Output Voltage
VOL
-6
“L-H” Propagation
TPLH
IIH = 16 mA
0.5
“L-H” Rise Time
TR
IIH = 16 mA
0.3
“H-L” Propagation
TPHL
IIH = 16 mA
1.0
“H-L” Fall Time
TF
IIH = 16 mA
0.3
Protection Threshold Voltage VOCP
9.5
MicroPower Direct
Protection Reset Time
TTIMER
Between Start & Cancel 1.0 1.4
292 Page Street
Suite D
Stoughton, MA 02072
USA
Fault Output Current
Controlled Time Detect
Soft Turn-Off Time
IFO
TTRIP1
TCF
See Note 6
5.0
Short Circuit 1, See Note 7
2.6
See Note 8
4.5
SC Detect Voltage
VSC
Collector Voltage of Module 15
T: [phone]
F: [phone]
E: [e-mail]
Notes:
1. Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
2. ”H” = high level signal. “L” = low level signal.
W: www.micropowerdirect.com
3. The voltage applied to pin 14.
4. The current measured between pins 13 and 14.
5. The input current at pin 15.
6. The input current at pin 15. R4 = 4.7 k⍀.
7. Pin 13 м 15 VDC. Pin 16 open.
8. Pin 13 м 15 VDC. Pin 14 open.
9. Pin 1 м 15 VDC.
www.micropowerdirect.com
Max.
13
16
50
25
VCC
+5.0
-5.0
3,750
+70
+125
20
Max.
12.4
15.5
20
18.0
-10.0
20
17.0
-10
1.0
1.0
1.3
1.0
2.0
Units
VDC
VDC
mA
VDC
A
VAC
ºC
ºC
mA
Units
VDC
kHz
⍀
VDC
kV/µS
mA
VDC
VDC
µS
µS
µS
µS
mS
mA
µS
µS
VDC