B1000RW_14 Datasheet, PDF (1/2 Pages) MicroPower Direct, LLC – B1000RW SERIES

B1000RW Series
Compact 1 x 2 Inch 10W
Wide Input Range
DC/DC Converters
Key Features:
• 10W Output Power
• UL Approved (File E245422)
• 2:1 Input Voltage Range
• 1,500 VDC Isolation
• Meets EN55022 Class “A”
• Compact 1 x 2 Inch Case
• Single & Dual Outputs
• Industry Standard Pin-Out
MicroPower Direct
292 Page Street
Suite D
Stoughton, MA 02072
USA
T: [phone]
F: [phone]
E: [e-mail]
W: www.micropowerdirect.com
Electrical Specifications
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Input
Parameter
Conditions
Min. Typ. Max. Units
12 VDC Input 8.0 8.5 9.0
Input Start Voltage
24 VDC Input 15.0 17.0 18.0
VDC
48 VDC Input 30.0 33.0 36.0
Input Filter
␲ (Pi) Filter (Complies with EN55022 Class “A”)
Reverse Polarity Input Current
2.0
A
Short Circuit Input Power
3,500 4,500
mW
Output
Parameter
Conditions
Min. Typ. Max. Units
Output Voltage Accuracy
±0.5 ±1.0
%
Output Voltage Balance
Dual Output , Balanced Loads
±0.5 ±1.0
%
Line Regulation
Vin = Min to Max
±0.1 ±0.3
%
Load Regulation
Iout = 10% to 100%
±0.1 ±0.5
%
Ripple & Noise (20 MHz) (Note 1)
50 75 mV P - P
Ripple & Noise (20 MHz)
Over Line, Load & Temp.
100 mV P - P
Ripple & Noise (20 MHz)
15 mV rms
Output Power Protection
120
%
Transient Recovery Time (Note 2)
Transient Response Deviation
25% Load Step Change
150 300
±2.0 ±4.0
µSec
%
Temperature Coefficient
±0.01 ±0.02 %/°C
Output Short Circuit
Continuous (Autorecovery)
General
Parameter
Conditions
Min. Typ. Max. Units
Isolation Voltage
60 Seconds 1,500
VDC
Isolation Test Voltage
Flash Tested For 1 Sec 1,650
VDC
Isolation Resistance
500 VDC 1,000
M⍀
Isolation Capacitance
100 kHz, 1V
120 160
pF
Switching Frequency
260 300 340
kHz
Environmental
Parameter
Conditions
Min. Typ. Max. Units
Operating Temperature Range
Ambient -40 +25 +71
°C
Operating Temperature Range
Case
+90
°C
Storage Temperature Range
-50
+125
°C
Cooling
Free Air Convection
Humidity
RH, Non-condensing
95
%
RFI
Six-Side Shielded Metal Case
Conducted EMI
EN55022 Class “A”
Physical
Case Size
2.0 x 1.0 x 0.40 Inches (50.8 x 25.4 x 10.2 mm)
Case Material
Metal with Non-Conductive Base (UL94-V0)
Weight
1.06 Oz (30g)
Reliability Specifications
Parameter
Conditions
Min. Typ. Max. Units
MTBF
MIL HDBK 217F, 25°C, Gnd Benign 700
kHours
Safety Standards
UL 1950, EN 60950, IEC 60950
Safety Approvals
UL, cUL; File No. E245422
Absolute Maximum Ratings
Parameter
Conditions
Min. Typ. Max. Units
12 VDC Input -0.7
25.0
Input Voltage Surge (1 Sec)
24 VDC Input -0.7
50.0
VDC
48 VDC Input -0.7
100.0
Lead Temperature
1.5 mm From Case For 10 Sec
260.0
°C
Internal Power Dissipation
All Models
5,000
mW
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
www.micropowerdirect.com