A200EHI_14 Datasheet, PDF (1/2 Pages) MicroPower Direct, LLC – A200EHI SERIES

A200EHI Series
Low Cost, Miniature DIP
2W, Very High Isolation
DC/DC Converters
Key Features:
• 2W Output Power
• 6,000 VDC Isolation
• UL Approved (File E245422)
• -40ºC to 85ºC Operation
• 24 Pin DIP Case
• 5V and 12V Inputs
• Single & Dual Outputs
• 16 Standard Models
• 3.5 MH MTBF
• LOWEST COST!!
Electrical Specifications
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Input
Parameter
Conditions
Min. Typ. Max. Units
Input Voltage Range
5 VDC Input 4.5 5.0 5.5
12 VDC Input 10.8 12.0 13.2
VDC
Input Filter
Internal Capacitor
Short Circuit Input Power
1,500
mW
Output
Parameter
Conditions
Min. Typ. Max. Units
Output Voltage Accuracy
±2.0 ±4.0
%
Output Voltage Balance
Dual Output , Balanced Loads
±1.0 ±3.0
%
Line Regulation
For Vin Change of 1%
±1.2
%/%
Load Regulation, 5V Input
Iout = 10% to 100%
±15
%
Load Regulation, 12V Input
Iout = 10% to 100%
±10
%
Ripple & Noise (20 MHz)
See Note 1
100 200 mV P - P
Output Power Protection
120
%
Temperature Coefficient
±0.03 %/ºC
Output Short Circuit
General
Parameter
Isolation Voltage
Isolation Resistance
Isolation Capacitance
Switching Frequency
Environmental
Parameter
Operating Temperature Range
Storage Temperature Range
Cooling
Humidity
Physical
Momentary (1.0 Seconds)
Conditions
Min. Typ.
60 Seconds 6,000
500 VDC 1,000
100 kHz, 1V
2
35
Max.
Units
VDC
M
pF
kHz
Conditions
Min. Typ.
Ambient -40
-55
Free Air Convection
RH, Non-condensing
Max.
+85
+125
95
Units
ºC
ºC
%
MicroPower Direct
292 Page Street
Suite D
Stoughton, MA 02072
USA
T: [phone]
F: [phone]
E: [e-mail]
W: www.micropowerdirect.com
Case Size
Case Material
Weight
Reliability Specifications
Parameter
MTBF
Safety Standards
Safety Approvals
Absolute Maximum Ratings
Parameter
Input Voltage Surge (1 Sec)
1.27 x 0.62 x 0.40 Inches (32.3 x 15.7 x 10.2 mm)
Non-Conductive Black Plastic (UL94-V0)
0.42 Oz (12g)
Conditions
MIL HDBK 217F, 25ºC, Gnd Benign
Min. Typ. Max. Units
3.5
MHours
UL 1950, EN 60950, IEC 60950
UL, cUL; File No. E245422
Conditions
Min. Typ. Max.
5 VDC Input -0.7
7.5
12 VDC Input -0.7
15.0
Units
VDC
Lead Temperature
1.5 mm From Case For 10 Sec.
300
ºC
Internal Power Dissipation
All Models
1,500
mW
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
www.micropowerdirect.com