A200EHI Datasheet, PDF (1/2 Pages) MicroPower Direct, LLC – Low Cost, Miniature DIP 2W, Very High Isolation DC/DC Converters

A200EHI _Series
Low Cost, Miniature DIP
2W, Very High Isolation
DC/DC Converters
Key Features:
• 2W Output Power
• 6,000 VDC Isolation
• UL Approved (File E245422)
• -40ºC to 85ºC Operation
• 24 Pin DIP Case
• 5V and 12V Inputs
• Single & Dual Outputs
• 16 Standard Models
• 3.5 MH MTBF
• LOWEST COST!!
Electrical Specifications
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Input
Parameter
Conditions
Min. Typ. Max. Units
Input Voltage Range
5 VDC Input 4.5 5.0 5.5
12 VDC Input 10.8 12.0 13.2
VDC
Input Filter
Internal Capacitor
Short Circuit Input Power
1,500
mW
Output
Parameter
Conditions
Min. Typ. Max. Units
Output Voltage Accuracy
±2.0 ±4.0
%
Output Voltage Balance
Dual Output , Balanced Loads
±1.0 ±3.0
%
Line Regulation
For Vin Change of 1%
±1.2
%/%
Load Regulation, 5V Input
Iout = 10% to 100%
±15
%
Load Regulation, 12V Input
Iout = 10% to 100%
±10
%
Ripple & Noise (20 MHz) (Note 1)
100 200 mV P - P
Output Power Protection
120
%
Temperature Coefficient
±0.03 %/ºC
Output Short Circuit
Momentary (1.0 Seconds)
General
Parameter
RoHS Compliant _{Isolation Voltage}
Conditions
Min. Typ. Max.
60 Seconds 6,000
Units
VDC
Isolation Resistance
500 VDC 1,000
MΩ
Isolation Capacitance
100 kHz, 1V
2
pF
Switching Frequency
35
kHz
Environmental
Parameter
Conditions
Min. Typ. Max. Units
Operating Temperature Range
Ambient -40
+85
ºC
Storage Temperature Range
-55
+125
ºC
Cooling
Free Air Convection
Humidity
RH, Non-condensing
95
%
MicroPower Direct
292 Page Street
Suite D
Stoughton, MA 02072
USA
Physical
Case Size
Case Material
Weight
Reliability Specifications
1.27 x 0.62 x 0.40 Inches (32.3 x 15.7 x 10.2 mm)
Non-Conductive Black Plastic (UL94-V0)
0.42 Oz (12g)
T: [phone]
F: [phone]
E: [e-mail]
W: www.micropowerdirect.com
Parameter
MTBF
Safety Standards
Safety Approvals
Conditions
Min. Typ.
MIL HDBK 217F, 25ºC, Gnd Benign 3.5
UL 1950, EN 60950, IEC 60950
UL, cUL; File No. E245422
Max.
Units
MHours
Absolute Maximum Ratings
Parameter
Conditions
Min. Typ. Max. Units
Input Voltage Surge (1 Sec)
5 VDC Input -0.7
12 VDC Input -0.7
7.5
VDC
15.0
Lead Temperature
1.5 mm From Case For 10 Sec.
300
ºC
Internal Power Dissipation
All Models
1,500
mW
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.