A1100RW Datasheet, PDF (1/2 Pages) MicroPower Direct, LLC – Miniature, 10W DIP Single & Dual Output DC/DC Converters

A1100RW _Series
Miniature, 10W DIP
Single & Dual Output
DC/DC Converters
Electrical Specifications
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Key Features:
• 10W Output Power
• Compact DIP Case
Input
Parameter
Input Start Voltage
Conditions
12 VDC Input
24 VDC Input
Min.
7.0
14.0
Typ.
8.0
16.0
Max.
9.0
18.0
Units
VDC
• 2:1 Input Voltage Range
• Single & Dual Outputs
Input Filter
Reverse Polarity Input Current
48 VDC Input 30.0 33.0 36.0
π (Pi) Filter (Complies with EN55022 Class “A”)
0.5
A
• 1,500 VDC Isolation
Short Circuit Input Power
2,500
mW
• Meets EN55022 Class “A”
• 1.0 MH MTBF
• Industry Standard Pin-Out
Output
Parameter
Output Voltage Accuracy
Output Voltage Balance
Conditions
Min.
Dual Output , Balanced Loads
Typ.
±0.6
±0.5
Max.
±1.2
±1.0
Units
%
%
Line Regulation
Vin = Min to Max
±0.3 ±1.0
%
Load Regulation, 2.5 Vout Models
Iout = 10% to 100%
±0.7 ±1.5
%
Load Regulation, All Other Models
Iout = 10% to 100%
±0.5 ±1.2
%
Ripple & Noise (20 MHz) (Note 1)
50 85 mV P - P
Ripple & Noise (20 MHz)
Over Line, Load & Temp.
100 mV P - P
Ripple & Noise (20 MHz)
15 mV rms
Output Power Protection
110 150 180
%
Transient Recovery Time (Note 2)
Transient Response Deviation
25% Load Step Change
250 500
±3.0 ±5.0
µSec
%
Temperature Coefficient
±0.01 ±0.02 %/ºC
Output Short Circuit
Continuous (Autorecovery)
General
Parameter
Conditions
Min. Typ. Max. Units
Isolation Voltage
60 Seconds 1,500
VDC
Isolation Voltage Test
Flash Tested for 1 Second 1,650
VDC
Isolation Resistance
500 VDC 1,000
MΩ
RoHS Compliant
Isolation Capacitance
Switching Frequency
100 kHz, 1V
1,000 1,200
pF
400
kHz
Environmental
Parameter
Conditions
Min. Typ. Max. Units
Operating Temperature Range
Ambient -40 +25 +60
ºC
Operating Temperature Range
Case -40
+90
ºC
Storage Temperature Range
-40
+125
ºC
MicroPower Direct
292 Page Street
Suite D
Stoughton, MA 02072
USA
Cooling
Humidity
Conducted EMI
Physical
Case Size
Free Air Convection
RH, Non-condensing
EN55022 Class “A”
95
%
1.25 x 0.80 x 0.40 Inches (31.8 x 20.3 x 10.2 mm)
T: [phone]
F: [phone]
E: [e-mail]
W: www.micropowerdirect.com
Case Material
Weight
Reliability Specifications
Parameter
MTBF
Metal with Non-Conductive Base
0.61 Oz (17.3g)
Conditions
Min. Typ. Max. Units
MIL HDBK 217F, 25ºC, Gnd Benign 1.0
MHours
Absolute Maximum Ratings
Parameter
Conditions
Min. Typ. Max. Units
12 VDC Input -0.7
25.0
Input Voltage Surge (1 Sec)
24 VDC Input -0.7
50.0
VDC
48 VDC Input -0.7
100.0
Lead Temperature
1.5 mm From Case For 10 Sec
260
ºC
Internal Power Dissipation
All Models
2,500
mW
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.