A100HI_14 Datasheet, PDF (1/2 Pages) MicroPower Direct, LLC – A100HI SERIES

A100HI ^Series
Ultra-High Isolation, 1.5W
Single & Dual Output
DC/DC Converters
Key Features:
• 1.5W Output Power
• 8,000 VDC Isolation
• 2 µA Leakage Current Max
• Compact DIP Case
• Single & Dual Outputs
• Meets EN55022 Class A
• 1.0 MH MTBF
• Industry Standard Pin-Out
MicroPower Direct
292 Page Street
Suite D
Stoughton, MA 02072
USA
T: [phone]
F: [phone]
E: [e-mail]
W: www.micropowerdirect.com
Electrical Specifications
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Input
Parameter
Conditions
Min. Typ. Max. Units
5 VDC Input 4.5 5.0 5.5
Input Voltage Range
12 VDC Input 10.8 12.0 13.2
VDC
15 VDC Input 13.5 15.0 16.5
Input Filter
 (Pi) Filter
Reverse Polarity Input Current
0.5
A
Short Circuit Input Power
1,000
mW
Output
Parameter
Conditions
Min. Typ. Max. Units
Output Voltage Accuracy
±2.0 ±4.0
%
Output Voltage Balance
Dual Output , Balanced Loads
±0.5 ±2.0
%
Line Regulation
For Vin Change of 1%
±1.2 ±1.5
%
Load Regulation, (Note 1)
See Model Selection Guide
Ripple & Noise (20 MHz) (Note 2)
30 40 mV P - P
Ripple & Noise (20 MHz)
Over Line, Load & Temp.
50 mV P - P
Ripple & Noise (20 MHz)
15 mV rms
Output Power Protection
120
%
Temperature Coefficient
±0.01 ±0.02 %/ºC
Output Short Circuit
Continuous
General
Parameter
Conditions
Min. Typ. Max. Units
Isolation Voltage, Rated
60 Seconds 8,000
VDC
Isolation Test Voltage
Flash Tested For 1 Second 8,800
VDC
Leakage Current
240 VAC, 60 Hz
2
µA
Isolation Resistance
500 VDC 10
G
Isolation Capacitance
100 kHz, 1V
10 15
pF
Switching Frequency
50
100
kHz
Environmental
Parameter
Conditions
Min. Typ. Max. Units
Operating Temperature Range
Ambient -40
+85
ºC
Operating Temperature Range
Case -40
+95
ºC
Storage Temperature Range
-55
+125
ºC
Cooling
Free Air Convection
Humidity
RH, Non-condensing
95
%
Physical
Case Size
1.25 x 0.80 x 0.40 Inches (31.8 x 20.3 x 10.2 mm)
Case Material
Non-Conductive Black Plastic (UL94-V0)
Weight
0.42 Oz (12g)
Reliability Specifications
Parameter
Conditions
Min. Typ. Max. Units
MTBF
MIL HDBK 217F, 25ºC, Gnd Benign 2.0
MHours
Absolute Maximum Ratings
Parameter
Conditions
Min. Typ. Max. Units
5 VDC Input -0.7
7.0
Input Voltage Surge (1 Sec)
12 VDC Input -0.7
17.0
VDC
15 VDC Input -0.7
21.0
Lead Temperature
1.5 mm From Case For 10 Sec
260
ºC
Internal Power Dissipation
All Models
1,000
mW
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
www.micropowerdirect.com