MC74VHC4066 Datasheet, PDF (2/12 Pages) Motorola, Inc – Quad Analog Switch/Multiplexer/Demultiplexer

MC74VHC4066
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _{MAXIMUM RATINGS*}
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _Symbol
Parameter
Value
Unit
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _VCC
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _VIS
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _Vin
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _I
Positive DC Supply Voltage (Referenced to GND)
Analog Input Voltage (Referenced to GND)
Digital Input Voltage (Referenced to GND)
DC Current Into or Out of Any Pin
– 0.5 to + 14.0
V
– 0.5 to VCC + 0.5 V
– 0.5 to VCC + 0.5 V
± 25
mA
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _{PD Power Dissipation in Still Air,}
SOIC Package†
500
mW
TSSOP Package†
450
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ^{Tstg StorageTemperature}
– 65 to + 150
_C
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ^{TL Lead Temperature, 1 mm from Case for 10 Seconds}
260
_C
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ^{* Maximum Ratings are those values beyond which damage to the device may occur.}
Functional operation should be restricted to the Recommended Operating Conditions.
†Derating — SOIC Package: – 7 mW/_C from 65_ to 125_C
TSSOP Package: – 6.1 mW/_C from 65_ to 125_C
This device contains protection
circuitry to guard against damage
due to high static voltages or electric
fields. However, precautions must
be taken to avoid applications of any
voltage higher than maximum rated
voltages to this high–impedance cir-
cuit. For proper operation, Vin and
v v ^{Vout should be constrained to the}
range GND (Vin or Vout) VCC.
Unused inputs must always be
tied to an appropriate logic voltage
level (e.g., either GND or VCC).
Unused outputs must be left open.
I/O pins must be connected to a
properly terminated line or bus.
RECOMMENDED OPERATING CONDITIONS
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ^Symbol
Parameter
Min Max Unit
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ^{VCC Positive DC Supply Voltage (Referenced to GND)}
2.0 12.0 V
VIS Analog Input Voltage (Referenced to GND)
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _Vin
Digital Input Voltage (Referenced to GND)
GND VCC V
GND VCC V
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _VIO*
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _TA
Static or Dynamic Voltage Across Switch
Operating Temperature, All Package Types
— 1.2 V
– 55 + 125 _C
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _{tr, tf Input Rise and Fall Time, ON/OFF Control}
ns
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _{Inputs (Figure 10)}
VCC = 2.0 V 0 1000
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ^{VCC=3.0V 0}
600
VCC = 4.5 V 0
500
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _{VCC=9.0V 0}
400
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ^{VCC=12.0V 0}
250
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ^{* For voltage drops across the switch greater than 1.2 V (switch on), excessive VCC current may}
be drawn; i.e., the current out of the switch may contain both VCC and switch input components.
The reliability of the device will be unaffected unless the Maximum Ratings are exceeded.
DC ELECTRICAL CHARACTERISTIC Digital Section (Voltages Referenced to GND)
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _Symbol
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ^VIH
Parameter
Minimum High–Level Voltage
ON/OFF Control Inputs
Test Conditions
Ron = Per Spec
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _VIL
Maximum Low–Level Voltage
Ron = Per Spec
ON/OFF Control Inputs
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _Iin
Maximum Input Leakage Current Vin = VCC or GND
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _{ON/OFF Control Inputs}
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _ICC
Maximum Quiescent Supply
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ^{Current (per Package)}
Vin = VCC or GND
VIO = 0 V
VCC
V
2.0
3.0
4.5
9.0
12.0
2.0
3.0
4.5
9.0
12.0
12.0
6.0
12.0
Guaranteed Limit
v v ^{– 55 to}
25_C
85_C
125_C Unit
1.5
1.5
1.5
V
2.1
2.1
2.1
3.15
3.15
3.15
6.3
6.3
6.3
8.4
8.4
8.4
0.5
0.5
0.5
V
0.9
0.9
0.9
1.35
1.35
1.35
2.7
2.7
2.7
3.6
3.6
3.6
± 0.1
± 1.0
± 1.0
µA
2
20
40
µA
4
40
160
MOTOROLA
2
VHC Data – Advanced CMOS Logic
DL203 — Rev 2