MMBZ5V6ALT1_07 Datasheet, PDF (18/27 Pages) Motorola, Inc – SOT-23 Dual Monolithic Common Anode Zener Transient Voltage Suppressor For ESD Protection

P6SMB6.8AT3 through P6SMB200AT3
ELECTRICAL CHARACTERISTICS (TA = 25°C unless otherwise noted).
Device{{
Reverse
Stand-Off Voltage
VR
Volts (1)
Breakdown Voltage*
VBR @ IT
Volts
Min
mA
Maximum
Clamping Voltage
VC @ Ipp
Volts
Peak
Pulse Current
(See Figure 2)
Ipp{
Amps
Maximum
Reverse Leakage
@ VR
IR
µA
Device
Marking
1SMB10CAT3
10
11.1
1.0
17.0
35.3
1SMB11CAT3
11
12.2
1.0
18.2
33.0
1SMB12CAT3
12
13.3
1.0
19.9
30.2
1SMB13CAT3
13
14.4
1.0
21.5
27.9
5.0
KXC
5.0
KZC
5.0
LEC
5.0
LGC
1SMB14CAT3
14
15.6
1.0
23.2
25.8
1SMB15CAT3
15
16.7
1.0
24.4
24.0
1SMB16CAT3
16
17.8
1.0
26.0
23.1
1SMB17CAT3
17
18.9
1.0
27.6
21.7
5.0
LKC
5.0
LMC
5.0
LPC
5.0
LRC
1SMB18CAT3
18
20.0
1.0
29.2
20.5
1SMB20CAT3
20
22.2
1.0
32.4
18.5
1SMB22CAT3
22
24.4
1.0
35.5
16.9
1SMB24CAT3
24
26.7
1.0
38.9
15.4
5.0
LTC
5.0
LVC
5.0
LXC
5.0
LZC
1SMB26CAT3
26
28.9
1.0
42.1
14.2
1SMB28CAT3
28
31.1
1.0
45.4
13.2
1SMB30CAT3
30
33.3
1.0
48.4
12.4
1SMB33CAT3
33
36.7
1.0
53.3
11.3
5.0
MEC
5.0
MGC
5.0
MKC
5.0
MMC
1SMB36CAT3
36
40.0
1.0
58.1
10.3
1SMB40CAT3
40
44.4
1.0
64.5
9.3
1SMB43CAT3
43
47.8
1.0
69.4
8.6
1SMB45CAT3
45
50.0
1.0
72.7
8.3
5.0
MPC
5.0
MRC
5.0
MTC
5.0
MVC
1SMB48CAT3
48
53.3
1.0
77.4
7.7
1SMB51CAT3
51
56.7
1.0
82.4
7.3
1SMB54CAT3
54
60.0
1.0
87.1
6.9
1SMB58CAT3
58
64.4
1.0
93.6
6.4
5.0
MXC
5.0
MZC
5.0
NEC
5.0
NGC
1SMB60CAT3
60
66.7
1.0
96.8
6.2
1SMB64CAT3
64
71.1
1.0
103
5.8
1SMB70CAT3
70
77.8
1.0
113
5.3
1SMB75CAT3
75
83.3
1.0
121
4.9
5.0
NKC
5.0
NMC
5.0
NPC
5.0
NRC
1SMB78CAT3
78
86.7
1.0
126
4.7
5.0
NTC
Note 1: A transient suppressor is normally selected according to the reverse ”Stand Off Voltage” (VR) which should be equal to or greater than the DC or continuous peak operating
voltage level.
* * VBR measured at pulse test current IT at an ambient temperaure of 25°C.
{{ Surge current waveform per Figure 2 and derate per Figure 3 of the General Data — 600 Watt at the beginning of this group.
{{ T3 suffix designates tape and reel of 2500 units.
ABBREVIATIONS AND SYMBOLS
VR
Stand Off Voltage. Applied reverse voltage to assure a
non-conductive condition (See Note 1).
V(BR)min This is the minimum breakdown voltage the device will
exhibit and is used to assure that conduction does not
occur prior to this voltage level at 25°C.
IPP
VC
Maximum Clamping Voltage. The maximum peak volt-
PP
age appearing across the transient suppressor when
IR
subjected to the peak pusle current in a one millisecond
time interval. The peak pulse voltages are the combina-
tion of voltage rise due to both the series resistance and
thermal rise.
Peak Pulse Current — See Figure 2
Peak Pulse Power
Reverse Leakage
Devices listed in bold, italic are Motorola preferred devices.
600 Watt Peak Power Data Sheet
5-72
Motorola TVS/Zener Device Data