SN54LS47 Datasheet, PDF (1/3 Pages) Motorola, Inc – BCD TO 7-SEGMENT DECODER/DRIVER

BCD TO 7-SEGMENT
DECODER/DRIVER
The SN54 / 74LS47 are Low Power Schottky BCD to 7-Segment Decod-
er / Drivers consisting of NAND gates, input buffers and seven AND-OR-IN-
VERT gates. They offer active LOW, high sink current outputs for driving
indicators directly. Seven NAND gates and one driver are connected in pairs
to make BCD data and its complement available to the seven decoding
AND-OR-INVERT gates. The remaining NAND gate and three input buffers
provide lamp test, blanking input / ripple-blanking output and ripple-blanking
input.
The circuits accept 4-bit binary-coded-decimal (BCD) and, depending on
the state of the auxiliary inputs, decodes this data to drive a 7-segment display
indicator. The relative positive-logic output levels, as well as conditions
required at the auxiliary inputs, are shown in the truth tables. Output
configurations of the SN54 / 74LS47 are designed to withstand the relatively
high voltages required for 7-segment indicators.
These outputs will withstand 15 V with a maximum reverse current of
250 µA. Indicator segments requiring up to 24 mA of current may be driven
directly from the SN74LS47 high performance output transistors. Display
patterns for BCD input counts above nine are unique symbols to authenticate
input conditions.
The SN54 / 74LS47 incorporates automatic leading and / or trailing-edge
zero-blanking control (RBI and RBO). Lamp test (LT) may be performed at any
time which the BI / RBO node is a HIGH level. This device also contains an
overriding blanking input (BI) which can be used to control the lamp intensity
by varying the frequency and duty cycle of the BI input signal or to inhibit the
outputs.
• Lamp Intensity Modulation Capability (BI/RBO)
• Open Collector Outputs
• Lamp Test Provision
• Leading / Trailing Zero Suppression
• Input Clamp Diodes Limit High-Speed Termination Effects
CONNECTION DIAGRAM DIP (TOP VIEW)
VCC f g a b c d e
16 15 14 13 12 11 10 9
SN54/74LS47
BCD TO 7-SEGMENT
DECODER/ DRIVER
LOW POWER SCHOTTKY
16
1
J SUFFIX
CERAMIC
CASE 620-09
16
1
N SUFFIX
PLASTIC
CASE 648-08
16
1
D SUFFIX
SOIC
CASE 751B-03
ORDERING INFORMATION
SN54LSXXJ
SN74LSXXN
SN74LSXXD
Ceramic
Plastic
SOIC
1 2 3 4 56 78
B C LT BI / RBO RBI D A GND
PIN NAMES
LOADING (Note a)
HIGH
LOW
A, B, C, D
RBI
LT
BI / RBO
a, to g
BCD Inputs
Ripple-Blanking Input
Lamp-Test Input
Blanking Input or
Ripple-Blanking Output
Outputs
0.5 U.L.
0.5 U.L.
0.5 U.L.
0.5 U.L.
1.2 U.L.
Open-Collector
0.25 U.L.
0.25 U.L.
0.25 U.L.
0.75 U.L.
2.0 U.L.
15 (7.5) U.L.
NOTES:
a) 1 Unit Load (U.L.) = 40 µA HIGH, 1.6 mA LOW.
b) Output current measured at VOUT = 0.5 V
The Output LOW drive factor is 7.5 U.L. for Military (54) and 15 U.L. for Commercial (74) Temperature Ranges.
LOGIC SYMBOL
71 2 63 5
A B C D LT RBI
BI/
a b c d e f g RBO
13 12 11 10 9 15 14 4
VCC = PIN 16
GND = PIN 8
FAST AND LS TTL DATA
5-56