MC10H173 Datasheet, PDF (1/4 Pages) Motorola, Inc – QUAD 2-INPUT MULTIPLEXER / LATCH

MOTOROLA
SEMICONDUCTOR TECHNICAL DATA
Quad 2-Input Multiplexer/
Latch
The MC10H173 is a quad 2–input multiplexer with latch. This device is a
functional/pinout duplication of the standard MECL 10K part, with 100%
improvement in propagation delay and no increase in power supply current.
• Data Propagation Delay, 1.5 ns Typical • Voltage Compensated
• Power Dissipation, 275 mW Typical
• MECL 10K–Compatible
• Improved Noise Margin 150 mV (over
operating voltage and temperature range)
MAXIMUM RATINGS
Characteristic
Symbol
Rating
Unit
Power Supply (VCC = 0)
Input Voltage (VCC = 0)
Output Current — Continuous
— Surge
VEE
–8.0 to 0
Vdc
VI
0 to VEE
Vdc
Iout
50
mA
100
Operating Temperature Range
Storage Temperature Range — Plastic
— Ceramic
TA
0 to +75
°C
Tstg
–55 to +150
°C
–55 to +165
°C
ELECTRICAL CHARACTERISTICS (VEE = –5.2 V ±5%) (See Note)
0°
25°
75°
Characteristic
Symbol Min Max Min Max Min Max Unit
Power Supply Current
Input Current High
Pins 3–7 & 10–13
Pin 9
IE
—
73
—
66
—
73
mA
IinH
µA
—
510
—
320
—
320
—
475
—
300
—
300
Input Current Low
High Output Voltage
Low Output Voltage
High Input Voltage
Low Input Voltage
AC PARAMETERS
IinL
VOH
VOL
VIH
VIL
0.5
—
0.5
—
0.3
—
µA
–1.02 –0.84 –0.98 –0.81 –0.92 –0.735 Vdc
–1.95 –1.63 –1.95 –1.63 –1.95 –1.60 Vdc
–1.17 –0.84 –1.13 –0.81 –1.07 –0.735 Vdc
–1.95 –1.48 –1.95 –1.48 –1.95 –1.45 Vdc
Propagation Delay
Data
Clock
Select
tpd
ns
0.7
2.3
0.7
2.3
0.7
2.3
1.0
3.7
1.0
3.7
1.0
3.7
1.0
3.6
1.0
3.6
1.0
3.6
Set–up Time
Data
Select
tset
ns
0.7
—
0.7
—
0.7
—
1.0
—
1.0
—
1.0
—
Hold Time
Data
Select
thold
ns
0.7
—
0.7
—
0.7
—
1.0
—
1.0
—
1.0
—
Rise Time
tr
0.7
2.4
0.7
2.4
0.7
2.4
ns
Fall Time
tf
0.7
2.4
0.7
2.4
0.7
2.4
ns
NOTE:
Each MECL 10H series circuit has been designed to meet the dc specifications shown in the test table,
after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed
circuit board and transverse air flow greater than 500 Iinear fpm is maintained. Outputs are terminated
through a 50–ohm resistor to –2.0 volts.
MC10H173
L SUFFIX
CERAMIC PACKAGE
CASE 620–10
P SUFFIX
PLASTIC PACKAGE
CASE 648–08
FN SUFFIX
PLCC
CASE 775–02
TRUTH TABLE
SELECT
H
L
X
CLOCK
L
L
H
Q0n _{+ 1}
D00
D01
Q0n
DIP
PIN ASSIGNMENT
Q0
1
Q1
2
D11
3
D10
4
D01
5
D00
6
CLOCK
7
VEE
8
16
VCC
15
Q2
14
Q3
13
D20
12
D21
11
D30
10
D31
9
SELECT
Pin assignment is for Dual–in–Line Package.
For PLCC pin assignment, see the Pin Conversion
Tables on page 6–11 of the Motorola MECL Data
Book (DL122/D).
3/93
© Motorola, Inc. 1996
2–53
REV 5