B0505XT-1WR2 Datasheet, PDF (4/5 Pages) MORNSUN Science& Technology Ltd. – 1W, FIXED INPUT, ISOLATED & UNREGULATED SINGLE OUTPUT

OUTLINE DIMENSIONS, RECOMMENDED FOOTPRINT & PACKAGING
MECHANICAL DIMENSIONS
RECOMMENDED FOOTPRINT
8.30 [0.327]
12.70 [0.500]
7.62
[0.300]
8
5
(Top View)
12
4
11.20 [0.441]
2.54 [0.100]
(Front View)
7.00 [0.276]
0.25 [0.010]
(Side View)
0.60 [0.024]
A
A
0.88 [0.035]
0.25 [0.010]
5 °max
Note:
Unit: mm[inch]
Pin section tolerances: ± 0.10mm[± 0.004inch]
General tolerances: ± 0.25mm[± 0.010inch]
8
5
10.50 [0.413]
12
4
1.70 [0.067]
1.00 [0.039]
Note: grid 2.54*2.54mm.
FOOTPRINT DETAILS
Pin
Function
1
G ND
2
Vin
4
0V
5
+Vo
8
NC
NC:No Connection
TUBE OUTLINE DIMENSIONS
6.70 [0.264]
15.10 [0.594]
10.70 [0.421]
[
9.50
0.374]
10.50
[0.413]
4.72 [0.186]
REEL PACKING OUTLINE DIMENSIONS
Taping dimension:
∅1.50 [0.059]
2.00 [0.079]
1.75 [0.069]
11.50 [0.453]
0.50 [0.020]
11.60 [0.457]
Taping reel dimension:
16.00 [0.630]
∅ 1.50 [0.059]
29.40 [1.157]
7.35 [0.289]
Note:
Unit: mm[inch]
General tolerances:±0.50mm[±0.020inch]
L=530mm[20.866inch] Devices per tube quantity: 40pcs
L=220mm[8.661inch] Devices per tube quantity: 15pcs
Short tube inner packaging dimensions:L*W*H=255*170*80mm
Short tube outer packaging dimensions(with six inner packaging):
L*W*H=375*280*270mm
Long tube inner packaging dimensions:L*W*H=580*200*100mm
Long tube outer packaging dimensions(with two inner packaging):
L*W*H=600*215*220mm
Long tube outer packaging dimensions(with three inner packaging):
L*W*H=600*215*325mm
∅ 100.00 [3.937]
∅ 13.00 [0.512]
Note:
∅ 21.50 [0.846]
Unit: mm[inch]
General tolerances: ±0.50mm[±0.020inch]
per reel of packing quantity: 500pcs
Inner packaging dimensions: L*W*H=365*350*105mm
Tube quantity:2000pcs
Outer packaging dimensions: L*W*H=365*350*105mm
Tube quantity:4000pcs
TEST CONFIGURATIONS
Input Reflected-Ripple Current Test Setup
Input reflected-ripple current is measured with an inductor Lin and Capacitor Cin to simulate source impedance.
Oscilloscope
Lin
DC DC ^Current
Cin Probe
Load
DESIGN CONSIDERATIONS
Lin(4.7µH) Cin(220µF, ESR < 1.0Ω at 100 KHz)
1) Requirement on output load
To ensure this module can operate efficiently and reliably, During operation, the minimum output load could not be less than 10% of the full load. If
the actual output power is very small, please connect a resistor with proper resistance at the output end in parallel to increase the load.
2) Overload Protection
Under normal operating conditions, the output circuit of these products has no protection against overload. The simplest method is to add a circuit
breaker to the circuit.
The copyright and authority for the interpretation of the products are reserved by MORNSUN
B_XT-1WR2 A/0-2012 Page 4 of 5