IB0505LS-W25 Datasheet, PDF (3/3 Pages) MORNSUN Science& Technology Ltd. – SINGLE OUTPUT DC-DC CONVERTER

OUTLINE DIMENSION & PIN CONNECTIONS
IB_LS-W25
MECHANICAL DIMENSIONS
(Front View)
10.00
[0.394]
0.50[0.020]
19.60[0.772]
(Bottom View)
12 4 6
2.54[0.100]
10.16
[0.400]
RECOMMENDED FOOTPRINT
∅1.00 [0.039]
12 4 6
Note: grid 2.54*2.54mm.
TUBE OUTLINE DIMENSIONS
9.60
[0.378]
FO O TP RI NT DE TA IL S
P in
Fu nction
1
Vin
2
GND
4
0V
6
+Vo
Note:
Unit : mm[ inch]
P in sect ion t ole ra nces: ±0. 10mm[ ±0. 004 inch ]
G ene ra l to leran ces: ±0. 25mm[± 0. 010inch]
IB_LD-W25
MECHANICAL DIMENSIONS
Note:
Unit :mm[inch]
4.90[0.193]
General tolerances: ±0.50mm[±0.020inch]
L=53 0mm[20.866 inch ] Devices per tube qua ntity: 2 5pcs
L=22 0mm[8.661inch] Devices pe r tu be quan tity: 10 pcs
Short tube in ner p ackaging dime nsion s: L*W*H=25 5*170*80 mm
Short tube outer p ackaging dime nsion s(with six inn er pa ckaging boxes):
L*W*H=37 5*280*27 0mm
Long tube in ner p ackaging dime nsion s: L*W*H=580*20 0*100mm
Long tube outer p ackaging dime nsion s(with two inne r packa gin g b oxes):
L*W*H=60 0*215*22 0mm
Long tube outer p ackaging dime nsion s(with three inner packag ing bo xes):
L*W*H=60 0*215*32 5mm
RECOMMENDED FOOTPRINT
(Front View)
0.50[0.020]
∅1.00[0.039]
14
11 9
1
7
20.00[0.787]
15.24[0.600]
1
7
(Bottom View)
14
11 9
7.62
[0.300]
12.70
[0.500]
Note: grid 2.54*2.54mm.
TUBE OUTLINE DIMENSIONS
12.50
[0.492]
FOOTPRINT DETAILS
Pin
Function
1
GND
7
NC
9
+Vo
11
0V
14
Vin
NC: No connection
No t e :
Un it : mm [ in ch ]
Pin section tolerances: ±0.10mm[±0.004inch]
G eneral tolerances:±0.25mm[±0.010inch]
3.50[0.138]
Note:
Unit :mm[inch]
General tolerances: ±0.50mm[±0.020inch]
L=530mm[20.866inch] Devices per tube quantity: 25pcs
L=220mm[8.661inch] Devices per tube quantity: 10pcs
Short tube inner packaging dimensions: L*W*H=255*170*80mm
Short tube outer packaging dimensions(with six inner packaging boxes):
L*W*H=375*280*270mm
Long tube inner packaging dimensions: L*W*H=580*200*100mm
Long tube outer packaging dimensions(with two inner packaging boxes):
L*W*H=600*215*220mm
Long tube outer packaging dimensions(with three inner packaging boxes):
L*W*H=600*21 5*325mm
Note:
1. Operation under minimum load will not damage the converter; However, they may not meet all specification listed.
2. All specifications measured at Ta=25°C, humidity<75%, nominal input voltage and rated output load unless otherwise specified.
3. Only typical models listed, other models may be different, please contact our technical person for more details.
4. In this datasheet, all the test methods of indications are based on corporate standards.
The copyright and authority for the interpretation of the products are reserved by Mornsun
Specifications subject to change without notice.
IB_LS-W25 & IB_LD-W25 A/1-2012 Page 3 of 3