B0505XD-1W Datasheet, PDF (2/3 Pages) MORNSUN Science& Technology Ltd. – DUAL/SINGLE OUTPUT DC-DC CONVERTER

ISOLATION SPECIFICATIONS
Item
Test conditions
Min. Typ. Max. Units
Isolation voltage
Tested for 1 minute and 1mA max 1000
VDC
Isolation resistance
Test at 500VDC
1000
MΩ
TYPICAL CHARACTERISTICS
OUTPUT SPECIFICATIONS
Item
Test conditions
Min Typ Max Units
Output power
Line regulation
For Vin change of 1%
0.1
1
W
±1.2 %
10% to 100% load (5V output)
12.8 15
Load regulation
10% to 100% load (9V output)
10% to 100% load (12V output)
8.3 15
%
6.8 15
10% to 100% load (15V output)
6.3 15
Output voltage accuracy
Temperature drift
100% full load
See tolerance envelope graph
0.03 %/°C
Ripple & Noise*
20MHz
Bandwidth
A_XD-1W
B_XD-1W
50
75
mVp-p
75 100
Switching frequency
Full load, nominal input
100
KHz
*Test ripple and noise by “parallel cable” method. See detailed operation instructions at Testing
of Power Converter section, application notes.
Note: Dual output models unbalanced load: ±5%.
APPLICATION NOTE
Operating Temp.(^oC)
RECOMMENDED CIRCUIT
Requirement on output load
To ensure this module can operate efficiently and reliably, During operation, the
minimum output load is not less than 10% of the full load, and that this product should
never be operated under no load! If the actual output power is very small, please
connect a resistor with proper resistance at the output end in parallel to increase the load,
or use our company’s products with a lower rated output power (A/B_XD-W25 Series).
Recommended testing and application circuit
If you want to further decrease the input/output ripple, an “LC” filtering network may be
connected to the input and output ends of the DC/DC converter, see (Figure 1).
It should also be noted that the inductance and the frequency of the “LC” filtering
network should be staggered with the DC/DC frequency to avoid mutual interference.
However, the capacitance of the output filter capacitor must be proper. If the capacitance
is too big, a startup problem might arise. For every channel of output, provided the safe
and reliable operation is ensured, the greatest capacitance of its filter capacitor sees
(Table 1).
Output Voltage Regulation and Over-voltage Protection Circuit
The simplest device for output voltage regulation, over-voltage and over-current
protection is a linear voltage regulator with overheat protection that is connected to the
input or output end in series (Figure 2).
Overload Protection
Under normal operating conditions, the output circuit of these products has no
protection against overload. The simplest method is to connect a self-recovery fuse in
series at the input end or add a circuit breaker to the circuit.
No parallel connection or plug and play
Dual Output
L
Vin
Cin
GND
Single Output
L
Vin
Cin
GND
DC DC
DC DC
L
+Vo
Cout
0V
L ^Cout
-Vo
L
+Vo
Cout
0V
(Figure 1)
Dual Output
Vin
REG
REG
+Vo
DC DC
0V
GND
REG
-Vo
Single Output
Vin
REG
REG
+Vo
DC DC
GND
0V
(Figure 2)
EXTERNAL CAPACITOR TABLE (Table 1)
Vin Cin Single Cout Dual Cout
(VDC) (uF) Vout (uF) Vout (uF)
(VDC)
(VDC)
5
4.7
5
10
±5 4.7
12 2.2
9
4.7 ±9 2.2
24
1
12 2.2 ±12 1
-
-
15
1 ±15 1
It’s not recommended to connect any external
capacitor in the application field with less than 0.5
watt output.
The copyright and authority for the interpretation of the products are reserved by Mornsun
Specifications subject to change without notice.
A_XD-1W & B_XD-1W A/1-2009 Page 2 of 3