B0303S-2W Datasheet, PDF (2/2 Pages) MORNSUN Science& Technology Ltd. – DUAL/SINGLE OUTPUT DC-DC CONVERTER

ISOLATION SPECIFICATIONS
Item
Test conditions
Min Typ
Isolation voltage Tested for 1 minute and 1 mA max 1000
Isolation resistance Test at 500VDC
1000
Max Units
VDC
MΩ
Overload Protection
Under normal operating conditions, the output
circuit of these products has no protection
against overload. The simplest method is to
connect a self-recovery fuse in series at the
input end or add a circuit breaker to the circuit.
OUTPUT SPECIFICATIONS
Item
Test conditions
Min Typ Max Units
Output power
Line regulation
For Vin change of 1%
0.2
2
W
±1.2
(5V output)
12.8 15
Load regulation
10% to 100% load
(9V output)
(12V output)
8.3
15
%
6.8
15
(15V output)
6.3
15
(24V output)
5
15
Output voltage accuracy
Temperature drift 100% full load
See tolerance envelope graph
0.03 %/°C
Ripple & Noise* 20MHz Bandwidth
75
150 mVp-p
Switching frequency Full load, nominal input
75
KHz
*Test ripple and noise by “parallel cable” method. See detailed operation instructions at Testing of Power
Converter section, application notes.
Note:
1. All specifications measured at TA=25°C, humidity<75%, nominal input voltage and rated output load
unless otherwise specified.
2. Dual output models unbalanced load: ±5%.
TYPICAL CHARACTERISTICS
Recommended testing and application circuit
If you want to further decrease the input/output
ripple, an “LC” filtering network may be
connected to the input and output ends of the
DC/DC converter, see (Figure 1).
Dual Output
L
Vin
Cin
GND
DC DC
L
+Vo
Cout
0V
L ^Cout
-Vo
Single Output
L
Vin
L
+Vo
Cin
DC DC
Cout
GND
0V
(Figure 1)
It should also be noted that the inductance and
the frequency of the “LC” filtering network should
be staggered with the DC/DC frequency to avoid
mutual interference. However, the capacitance of
the output filter capacitor must be proper. If the
capacitance is too big, a startup problem might
arise. For every channel of output, provided the
safe and reliable operation is ensured, the
greatest capacitance of its filter capacitor sees
(Table 1).
Ambient Temperature( C )
OUTLINE DIMENSIONS & PIN CONNECTIONS
First Angle Projection
RECOMMENDED FOOTPRINT
Top view,grid:2.54*2.54mm(0.1*0.1inch)
di a me t e r: 1 . 0 0 mm ( 0. 0 3 9 i n ch )
Dual Output
(0.079)
(0.100)
1 2 456
Single Output
12 4 6
(0.020)
No te:
Un i t:m m(i n ch )
Pin section:0.50*0.30mm(0.020*0.012inch)
Pin tolerances: 0.10mm( 0.004inch)
General tolerances: 0.25mm( 0.010inch)
FOOTPRINT DETAILS
Pin
Si ng les
1
Vin
2
GND
4
0V
5
No Pin
6
+Vo
Du a l s
Vin
GND
-V0
0V
+Vo
APPLICATION NOTE
Requirement on output load
To ensure this module can operate efficiently and reliably, During operation, the minimum
output load is not less than 10% of the full load, and that this product should never be
operated under no load! If the actual output power is very small, please connect a resistor
with proper resistance at the output end in parallel to increase the load, or use our company’s
products with a lower rated output power (A_S-1W /B_LS-1W Series).
EXTERNAL CAPACITOR TABLE (TABLE 1)
Vin Cin Single Cout Dual Cout
(VDC) (uF) Vout (uF) Vout (uF)
(VDC)
(VDC)
5
4.7
5
10
±5
4.7
12
2.2
9
4.7
±9
2.2
15
2.2
12
2.2
±12
1
24
1
15
1
±15 0.47
It’s not recommended to connect any external
capacitor in the application field with less than 0.5
watt output.
Output Voltage Regulation and Over-voltage
Protection Circuit
The simplest device for output voltage
regulation, over-voltage and over-current
protection is a linear voltage regulator with
overheat protection that is connected to the input
or output end in series (Figure 2).
Dual O u tput
Vi n
R EG
REG
DC DC
GND
REG
S ingle Output
Vi n
R EG
REG
GND
DC DC
(Figure 2)
+Vout
0V
-Vo ut
+Vout
0V
No parallel connection or plug and play.
MORNSUN reserves the copyright
Specifications subject to change without notice.
A_S-2W & B_S-2W A/1-2008
Page 2 of 2