QP12W05S-37A-L Datasheet, PDF (1/3 Pages) MORNSUN Science& Technology Ltd. – Hybrid Integrated IGBT Driver

QP12W05S-37A-L
Hybrid Integrated IGBT Driver
QP12W05S-37A-L is a hybrid integrated IGBT driver designed for
driving IGBT modules. This device is a fully isolated gate drive circuit
consisting of an optimally isolated gate drive amplifier and an isolated
DC-to-DC converter. The gate driver provides an over-current protection
function based on desaturation detection and fault output.
RoHS
Features
l Built in high CMRR opto-coupler（CMR：
Typical：30kV/µs，Min.：15kV/µs）
l Single supply drive topology
l Built in the isolated type DC/DC converter
for gate drive
l SIP package
l CMOS&TTL compatible
l Electrical isolation voltage between input
and output is 3750VRMS (for 1 minute)
l Built in short circuit protection circuit with a
pin for fault output
l Soft turn-off time is adjustable
l The drive signal is ignored in the blocking
time and the protection circuit reset at the
end of it
l Controlled time detect short circuit is
adjustable
l Switching frequency up to 20kHz
Application
l General-purpose Inverter
l AC Servo Systems
l Uninterruptable Power Supplies(UPS)
l Welding Machines
Recommended modules
l 600V Series IGBT(up to 600A)
l 1200V Series IGBT(up to 400A)
l 1700V Series IGBT(up to 200A)
MORNSUN Science & Technology Co.,Ltd.
Address: No. 5, Kehui St. 1, Kehui
development center, Science Ave.,
Guangzhou Science City, Luogang district,
Guangzhou,P.R.China.
Tel: [phone]
Fax:[phone]
Http://www.mornsun-power.com
Absolute Maximum Ratings
Item
Test Conditions
Supply Voltage
VD DC
Input Current
Out Voltage
Iin Between pin3 and pin4
VO When the Output voltage “H”
Output Current
Ig o n _{Pulse width 2µs}
Ig off ^{Frequency f=20kHz}
Isolation Voltage
Viso Sine wave voltage 50Hz/60 Hz,1 min.
Operation Temperature
T_op
Storage Temperature
T_st
Fault Output Current
IFO Pin15 input current
Input Voltage
V_R1 Applied pin13
Notes: 1. Ta=25℃；V_D=12V, unless otherwise specified
Ratings
13
25
V_CC
+5
-5
3750
-40 ~ +70
-50 ~ +125
20
50
Units
V
mA
V
A
A
V
°C
°C
mA
V
Electrical Characteristic
Characteristics
Test Conditions
Supply Voltage
“H” input current
Switching frequency
VD Recommended Range
IIH Recommended Range
ƒ Recommended Range
Gate resistant
Rg Recommended Range
VCC
Gate supply voltage
VEE
“H” output voltage
VOH
“L” output voltage
VOL
“L-H” propagation delay time tPLH
“L-H” rise time
tr
“H-L” propagation delay time tPHL
“H-L” fall time
tf
VD=12V
VD=12V
10KΩconnected between pin9-11
10KΩconnected between pin9-11
IIH=10mA
IIH=10mA
IIH=10mA
IIH=10mA
Protection threshold voltage VOCP V_D=12V
Protection reset time
ttimer Between start and cancel
Fault output current
Short-circuit detection time
delay
Soft turn-off time
IFO Pin15 input current,R=4.7K
Ttrip1 Pin 13: ≥15V,Pin 16:open
Tcf PIN 13≥15V，Pin 14:open
SC detect voltage
VSC Collector voltage of module
Notes：1. Ta=25℃，V_D=12V,Rg=5Ω. unless otherwise specified
2.＂H＂represents high level; ＂L＂represents low level.
Min
11.6
10
0
2
14.5
-7
13.5
-6
1
15
Limit
Typ.
12
16
15.3
0.5
0.3
1
0.3
9.5
1.4
5
1.6
4.5
Max
12.4
20
20
18.0
-10
17.0
-10
1
1
1.3
1
15
2
Units
V
mA
kHz
Ω
V
V
V
V
µs
µs
µs
µs
V
ms
mA
µs
µs
V
The copyright and authority for the interpretation of the products are reserved by MORNSUN
Specifications subject to change without notice.
QP12W 05S-37A-L
A/0-2012
Page 1 of 3