QP12W05S-37 Datasheet, PDF (1/3 Pages) MORNSUN Science& Technology Ltd. – Hybrid Integrated IGBT Driver

QP12W05S-37
Hybrid Integrated IGBT Driver
QP12W05S-37 is a hybrid integrated IGBT driver designed for driving
IGBT modules. This device is a fully isolated gate drive circuit consisting
of an optimally isolated gate drive amplifier and an isolated DC-to-DC
converter. The gate driver provides an over-current protection function
based on desaturation detection and fault output.
multi-country patent protection RoHS
Features
l Built in high CMRR opto-coupler (CMR:
Typical: 30kV/µs, Min.:15kV/µs)
l Single supply drive topology
l Built in the isolated type DC/DC
converter for gate drive
l SIP package
l CMOS&TTL compatible
l Electrical isolation voltage between input
and output is 3750VRMS (for 1 minute)
l Built in short circuit protection circuit with
a pin for fault output
l Soft turn-off time is adjustable
l The drive signal is ignored in the
blocking time and the protection circuit
reset at the end of it
l Controlled time detect short circuit is
adjustable
l Switching frequency up to 20kHz
Application
l General-purpose Inverter
l AC Servo Systems
l Uninterruptable Power Supplies(UPS)
l Welding Machines
Recommended modules
l 600V Series IGBT(up to 600A)
l 1200V Series IGBT(up to 400A)
l 1700V Series IGBT(up to 200A)
MORNSUN Science & Technology co.,Ltd.
Address: 2th floor 6th building, Huangzhou
Industrial District, Guangzhou, China
Tel: [phone]
Fax:[phone]
Http://www.mornsun-power.com
Absolute Maximum Ratings
Item
Test Conditions
Supply Voltage
Input Voltage
Out Voltage
V_D DC
V_I Between pin3 and pin4
V_O When the Output voltage “H”
Output Current
Isolation Voltage
Operation Temperature
I_{g on Pulse width 2µs}
I_{g off} ^{Frequency f=20kHz}
V_is Sine wave voltage 50Hz/60 Hz,1 min.
T_o
Storage Temperature
T_st
Fault Output Current
I_F
Input Voltage
V_R Applied pin13
Notes: 1. Ta=25ºC; VD=15V, unless otherwise specified.
Ratings
16
-1 ~ +7
VCC
+5
-5
3750
-40 ~ +70
-50 ~ +125
20
50
Units
V
V
V
A
A
V
ºC
ºC
mA
V
Electrical Characteristic
Charact eristics
Test Conditions
Min
Supply Voltage
VD Recommended Range
14.5
Pull-up voltage on input side VIN Recommended Range
4.75
“H” input current
IIH Recommended Range
—
Switching frequency
ƒ Recommended Range
Gate resistant
Rg
VC
Gate supply voltage
V^C E
“H” output voltage
E
VOH
“L” output voltage
VOL
“L-H” propagation delay time tPLH
“L-H” rise time
tr
“H-L” propagation delay time tPHL
“H-L” fall time
tf
Recommended Range
—
—
15KΩconnected between pin9-11
15KΩconnected between pin9-11
IIH=10mA
IIH=10mA
IIH=10mA
IIH=10mA
2
14.5
-7
13.5
-6
—
Protection threshold voltage VOCP VD=15V
Protection reset time
ttimer Between start and cancel
1
Fault output current
Short-circuit detection time
delay
Soft turn-off time
IFO Pin15 input current, R=4.7K
Ttrip1 Pin 13: ≥15V, Pin 16:open
Tcf PIN 13≥15V, Pin 16:open
SC detect voltage
VSC Collector voltage of module
15
Notes: 1. Ta=25 ºC, VD=15V, Rg=5Ω. unless otherwise specified
2.”H” represents high level; “L” represents low level.
Limit
Typ.
15
5
16
—
—
15.3
—
0.5
0.3
1
0.3
9.5
1.4
5
1.6
4.5
Max
15.5
5.25
—
20
18.0
-10
17.0
-10
1
1
1.3
1
2
Units
V
V
mA
kHz
Ω
V
V
V
V
µs
µs
µs
µs
V
ms
mA
µs
µs
V
The copyright and authority for the interpretation of the products are reserved by Mornsun
Specifications subject to change without notice.
QP12W 05S-37
A/1-2009
Page 1 of 3