QC841 Datasheet, PDF (1/2 Pages) MORNSUN Science& Technology Ltd. – Hybrid Integrated IGBT Driver

QC841
Hybrid Integrated IGBT Driver
QC841 is a hybrid integrated IGBT driver built-in electrical
isolation between power devices and control circuits with the high
CMRR opto-coupler. Short circuit protection is provided by a
built-in desaturation detector. A fault signal is provided if the short
circuit protection is activate
FEATURES
● Built in high CMRR opto-coupler
(CMR:Typical:30kV/µs, Min.:15kV/µs)
● Electrical isolation voltage between input and
output with opto-couplers
(Viso=3750VRMS/min)
● Switching frequency up to 20kHz
● Single supply drive topology
● Built in short circuit protection circuit with a
pin for fault output
● Soft IGBT turn-off and protection circuit time
reset
● Pins are compatible with EXB841
ABSOLUTE MAXIMUM RATINGS
Item
Test Conditions
Limit
Supply Voltage*
Input Voltage
VCC DC
VI Between Pin14 and Pin15
25
-1~+7
Photo coupler input current Iin Between Pin14 and Pin15
25
Output current
Ig on _{Pulse width 2µs}
Ig off ^{Frequency f=20kHz}
+5
-5
Isolation Voltage
Viso Sinewave voltage 50Hz/60Hz 1 min. 3750
Operation Temperature
Topr
-20~+70
Storage Temperature
Tstg
-40~+125
Fault Output Current
IFO
20
Input Voltage
VR1 Pin6 input voltage
50
Note：Ta=25°C; unless otherwise specified.
Units
V
V
mA
A
A
V
°C
°C
mA
V
APPLICATION
l General-purpose Inverter
l AC Servo Systems
l Uninterruptable Power Supplies(UPS)
l Welding Machines
RECOMMENDED MODULES
l 600V Series IGBT(up to 600A)
l 1200V Series IGBT(up to 400A)
l 1700V Series IGBT(up to 200A)
MORNSUN Science & Technology co.,Ltd.
Address: 2th floor 6th building, Huangzhou
Industrial District, Guangzhou, China
Tel: [phone]
Fax:[phone]
Http://www.mornsun-power.com
ELECTRICAL CHARACTERISTIC
Charact eristics
Test Conditions
Min
Supply Voltage
VCC Recommended Range
18
Pull-up voltage on input side VIN
Reverse bias power supply
voltage
VRB
“H” input current
IIH
Switching frequency
ƒ
Recommended Range
Recommended Range
Recommended Range
Recommended Range
4.75
15.2
Gate resistor
“H” input current
“H” output voltage
“L” output voltage
“L-H” propagation
“L-H” rise time
“H-L” propagation
“H-L” fall time
RG Recommended Range
2
IIH VIN=5V
-
VOH VCC=20V
13
VOL VCC=20V
-
tPLH IIH=16mA
-
tr IIH=16mA
tPHL IIH=16mA
tf IIH=16mA
Protection threshold voltage VOCP VCC=20V
Protection reset time
ttimer
1
Fault output current
Soft turn-off time
IFO Pin5 input current, R=4.7K
Toff2 Pin6: ≥15V, Pin11:open
Controlled time detect
short circuit 1
Ttrip1 Pin6: ≥15V, Pin11:open
Note: 1. Ta=25°C, VCC=15V. unless otherwise specified
2. ”H” represents high level; “L” represents low level.
Value
Typ.
20
5
-5
16
16
14
-5
0.5
0.6
1
0.4
8.5
1.4
5
2.6
Max
22
5.25
19
20
-
-
-
1
1
1.3
1
2
5
Units
V
V
V
mA
kHz
Ω
mA
V
V
µs
µs
µs
µs
V
ms
mA
µs
µs
The copyright and authority for the interpretation of the products are reserved by Mornsun
Specifications subject to change without notice.
QC841
A/1-2008
Page 1 of 2