MVIP5 Datasheet, PDF (1/2 Pages) MMD Components – MIL-STD-883 Level B Screening Available

MVIP, MVIL & MVIV Series VCXO
 MIL-STD-883 Level B Screening Available
 Available to -55°C to + 125°C Operating
 RoHS Compliant
 Less than 1 pSec Jitter
Frequency Range
Frequency Stability*
Operating Temp.Range
Storage Temp. Range
Aging
Logic “0”
Logic “1”
Supply Voltage (Vdd)
Supply Current
Symmetry (50% of waveform)
Rise / Fall Time (20% to 80%)
Load
Start Time
Phase Jitter (12kHz to 20MHz)
+2.5VDC ± 5%
+3.3VDC ± 5%
+5.0VDC ± 5%
Tri-State Operation
* Inclusive of Temp., Load and Voltage
Control Voltage (Vc)
Pullability
Linearity
+2.5VDC
+3.3VDC
+5.0VDC
LVDS
LVPECL
PECL
70.000MHz to 800.000MHZ
(See Part Number Guide for Options)
(See Part Number Guide for Options)
-55°C to +125°C
±5 ppm / yr max
1.43V typ
Vdd – 1.620 VDC max
Vdd – 1.620 VDC max
1.10V typ
Vdd- 1.025 vdc min
Vdd- 1.025 vdc min
50 mA max
50 mA max
N/A
60 mA max
60 mA max
N/A
N/A
N/A
140 mA max
(See Part Number Guide for Options)
2nSec max
50 Ohms into Vdd-2.00 VDC
10m Sec max
Less than 1 pSec
Vih = 70% of Vdd min to Enable Output
Vil = 30% max or grounded to Disable Output (High Impedance)
1.25VDC ±1.00VDC
1.65VDC ±1.50VDC
N/A
1.25VDC ±1.00VDC
1.65VDC ±1.50VDC
N/A
(See Part Number Guide for Options)
(See Part Number Guide for Options)
N/A
N/A
2.50VDC ±2.00VDC
Environmental & Mechanical Detail
Marking Detail
Shock
Solderability
Solvent Re-
sistance
Vibration
Gross Leak
Test
Fine Leak Test
MSL
MIL-STD-883, Method 2002 Cond B
MIL-STD-883, Method 2003
MIL-STD-202, Method 215
MIL-STD-883, Method 2007, Cond A
MIL-STD-883, Method 1014, Cond C
MIL-STD-883, Method 1014, Cond A2
Level 1 per IPC/JEDEC J-STD 20
Line 1 = MXXXXX
M = MMD
XXXXX = Frequency in MHZ
Line 2 = SYYWWL
S = Internal Code
YYWW
=
4 Numerical Digit Date Code
(Year / Week) Jan 27 2011=1105
L = Denotes RoHS Compliant
Line 3 = XXXXX
Internal use only
May vary with lots
Black dot to denote Pin 1
MMD MONITOR/QUARTZEK – An ILSI Company,
5458 Louie Lane, Reno, NV 89511
Phone: [phone], www.mmdcomp.com
Revisions only with customer approval
Revision:
07/31/13 D
Pg 1 of 2