M37736M4BXXXGP Datasheet, PDF (9/32 Pages) Mitsubishi Electric Semiconductor – SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER

PRELIMINARY _{NSootimcee: pTahriasmisentroict} ^{alimfinitsalasrpeescuifbicjeactitotno. change.}
MITSUBISHI MICROCOMPUTERS
M37736M4BXXXGP
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
ABSOLUTE MAXIMUM RATINGS
Symbol
Vcc
AVcc
VI
VI
VO
Pd
Topr
Tstg
Parameter
Conditions
Power source voltage
Analog power source voltage
_____
Input voltage RESET, CNVss, BYTE
Input voltage P00 – P07, P10 – P17, P20 – P27,
P30 – P33, P40 – P47, P50 – P57,
P60 – P67, P70 – P77, P80 – P87,
P90 – P92, P100 – P107,
VREF, XIN, BSEL
Output voltage P00 – P07, P10 – P17, P20 – P27,
P30 – P33, P40 – P47, P50 – P57,
P60 – P67, P70 – P77, P80 – P8_{_}7,
P90 – P97, P100 – P107, XOUT, E
Power dissipation
Ta = 25 °C
Operating temperature
Storage temperature
Ratings
Unit
–0.3 to +7
V
–0.3 to +7
V
–0.3 to +12
V
–0.3 to Vcc + 0.3
V
–0.3 to Vcc + 0.3
V
300
mW
–20 to +85
°C
–40 to +150
°C
RECOMMENDED OPERATING CONDITIONS (Vcc = 5 V ± 10%, Ta = –20 to +85 °C, unless otherwise noted)
Symbol
Vcc
AVcc
Vss
AVss
VIH
VIH
VIH
VIL
VIL
VIL
IOH(peak)
IOH(avg)
IOL(peak)
IOL(peak)
IOL(avg)
IOL(avg)
f(XIN)
f(XCIN)
Parameter
Power source voltage
f(XIN) : Operating
f(XIN) : Stopped, f(XCIN) = 32.768 kHz
Analog power source voltage
Power source voltage
Analog power source voltage
High-level input voltage P00 – P07, P30 – P33, P40 – P47, P50 – P57_{_} , P_{_}6_{_}0_{_}–_{_} P67,
P70 – P77, P80 – P87, P90 – P92, P100 – P107, XIN, RESET,
CNVss, BYTE, BSEL, XCIN (Note 3)
High-level input voltage P10 – P17, P20 – P27 (in single-chip mode)
High-level input voltage P10 – P17, P20 – P27
(in memory expansion mode and microprocessor mode)
Low-level input voltage P00 – P07, P30 – P33, P40 – P47, P50 – P57,_{_}P_{_}6_{_}0_{_}–_{_}P67,
P70 – P77, P80 – P87, P90 – P92, P100 – P107, XIN, RESET,
CNVss, BYTE, BSEL, XCIN (Note 3)
Low-level input voltage P10 – P17, P20 – P27 (in single-chip mode)
Low-level input voltage P10 – P17, P20 – P27
(in memory expansion mode and microprocessor mode)
High-level peak output current P00 – P07, P10 – P17, P20 – P27, P30 – P33,
P40 – P47, P50 – P57, P60 – P67, P70 – P77,
P80 – P87, P90 – P97, P100 – P107
High-level average output current P00 – P07, P10 – P17, P20 – P27, P30 – P33,
P40 – P47, P50 – P57, P60 – P67, P70 – P77,
P80 – P87, P90 – P97, P100 – P107
Low-level peak output current P00 – P07, P10 – P17, P20 – P27, P30 – P33,
P40 – P43, P54 – P57, P60 – P67, P70 – P77,
P80 – P87, P90 – P97, P104 – P107
Low-level peak output current P44 – P47, P100 – P103
Low-level average output current P00 – P07, P10 – P17, P20 – P27, P30 – P33,
P40 – P43, P54 – P57, P60 – P67, P70 – P77,
P80 – P87, P90 – P97, P104 – P107
Low-level average output current P44 – P47, P100 – P103
Main-clock oscillation frequency (Note 4)
Sub-clock oscillation frequency
Min.
4.5
2.7
0.8 Vcc
0.8 Vcc
0.5 Vcc
0
0
0
Notes 1. Average output current is the average value of a 100 ms interval.
2. The sum of IOL(peak) for ports P0, P1, P2, P3, P8, and P9 must be 80 mA or less,
the sum of IOH(peak) for ports P0, P1, P2, P3, P8, and P9 must be 80 mA or less,
the sum of IOL(peak) for ports P4, P5, P6, P7, and P10 must be 100 mA or less, and
the sum of IOH(peak) for ports P4, P5, P6, P7, and P10 must be 80 mA or less.
3. Limits VIH and VIL for XCIN are applied when the sub clock external input selection bit = “1”.
4. The maximum value of f(XIN) = 12.5 MHz when the main clock division selection bit = “1”.
Limits
Typ.
5.0
Vcc
0
0
Max.
5.5
5.5
Vcc
Vcc
Vcc
0.2Vcc
0.2Vcc
0.16Vcc
–10
–5
10
20
5
15
25
32.768
50
Unit
V
V
V
V
V
V
V
V
V
V
mA
mA
mA
mA
mA
mA
MHz
kHz
9