M38512M4 Datasheet, PDF (42/61 Pages) Mitsubishi Electric Semiconductor – SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER

MITSUBISHI MICROCOMPUTERS
3851 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
ELECTRICAL CHARACTERISTICS
Table 11 Absolute maximum ratings
Symbol
VCC
VI
VI
VI
VI
VO
VO
Pd
Topr
Tstg
Parameter
Power source voltage
Input voltage P00–P07, P10–P17, P20, P21,
P24–P27, P30–P34, P40–P44,
VREF
Input voltage P22, P23
Input voltage RESET, XIN
Input voltage CNVSS
Output voltage P00–P07, P10–P17, P20, P21,
P24–P27, P30–P34, P40–P44,
XOUT
Output voltage P22, P23
Power dissipation
Operating temperature
Storage temperature
Conditions
All voltages are based on VSS.
Output transistors are cut off.
Ta = 25 °C
Ratings
Unit
–0.3 to 7.0
V
–0.3 to VCC +0.3
V
–0.3 to 5.8
V
–0.3 to VCC +0.3
V
–0.3 to 13
V
–0.3 to VCC +0.3
V
–0.3 to 5.8
V
300
mW
–20 to 85
°C
–40 to 125
°C
Table 12 Recommended operating conditions (1)
(VCC = 2.7 to 5.5 V, Ta = –20 to 85 °C, unless otherwise noted)
Symbol
VCC
VSS
VREF
AVSS
VIA
VIH
VIH
VIH
VIH
VIH
VIH
VIL
VIL
Parameter
Power source voltage (At 8 MHz)
Power source voltage (At 4 MHz)
Power source voltage
A-D convert reference voltage
Analog power source voltage
Analog input voltage
AN0–AN4
“H” input voltage
P00–P07, P10–P17, P20–P27, P30–P34, P40–P44
“H” input voltage (when I²C-BUS input level is selected)
SDA1, SCL1
“H” input voltage (when I²C-BUS input level is selected)
SDA2, SCL2
“H” input voltage (when SMBUS input level is selected)
SDA1, SCL1
“H” input voltage (when SMBUS input level is selected)
SDA2, SCL2
“H” input voltage
RESET, XIN, CNVSS
“L” input voltage
P00–P07, P10–P17, P20–P27, P30–P34, P40–P44
“L” input voltage (when I²C-BUS input level is selected)
SDA1, SDA2, SCL1, SCL2
Limits
Unit
Min. Typ. Max.
4.0
5.0
5.5
V
2.7
5.0
5.5
0
V
2.0
VCC
V
0
V
AVSS
VCC
V
0.8VCC
VCC
V
0.7VCC
5.8
V
0.7VCC
VCC
V
1.4
5.8
V
1.4
0.8VCC
0
0
VCC
V
VCC
V
0.2VCC V
0.3VCC V
VIL
VIL
VIL
ΣIOH(peak)
ΣIOH(peak)
ΣIOL(peak)
ΣIOL(peak)
ΣIOL(peak)
ΣIOH(avg)
ΣIOH(avg)
ΣIOL(avg)
ΣIOL(avg)
ΣIOL(avg)
“L” input voltage (when SMBUS input level is selected)
SDA1, SDA2, SCL1, SCL2
“L” input voltage
RESET, CNVSS
“L” input voltage
XIN
“H” total peak output current P00–P07, P10–P17, P30–P34 (Note)
“H” total peak output current P20, P21, P24–P27, P40–P44 (Note)
“L” total peak output current P00–P07, P10–P12, P30–P34 (Note)
“L” total peak output current P13–P17 (Note)
“L” total peak output current P20–P27,P40–P44 (Note)
“H” total average output current P00–P07, P10–P17, P30–P34 (Note)
“H” total average output current P20, P21, P24–P27, P40–P44 (Note)
“L” total average output current P00–P07, P10–P12, P30–P34 (Note)
“L” total average output current P13–P17 (Note)
“L” total average output current P20–P27,P40–P44 (Note)
0
0.6
V
0
0.2VCC V
0
0.16VCC V
–80 mA
–80 mA
80 mA
80 mA
80 mA
–40 mA
–40 mA
40 mA
40 mA
40 mA
Note : The total output current is the sum of all the currents flowing through all the applicable ports. The total average current is an average value measured
over 100 ms. The total peak current is the peak value of all the currents.
42