PS21342-N Datasheet, PDF (4/9 Pages) Mitsubishi Electric Semiconductor – Intelligent Power Module TRANSFER-MOLD TYPE INSULATED TYPE

MITSUBISHI SEMICONDUCTOR <Intelligent Power Module>
PS21342-N
TRANSFER-MOLD TYPE
INSULATED TYPE
THERMAL RESISTANCE
Symbol
Parameter
Condition
Limits
Min.
Typ.
Max. ^Unit
Rth(j-f)Q
Rth(j-f)F
Junction-to-heat sink thermal ^{Inverter IGBT part (per 1/6 module)}
resistance
Inverter FWD part (per 1/6 module)
(Note 3)
—
—
6.0 °C/W
(Note 3)
—
—
6.5 °C/W
Note 3 : Grease with good thermal conductivity should be applied evenly about +100µm~+200µm on the contact surface of a DIP-IPM and a
heat sink.
ELECTRICAL CHARACTERISTICS (Tj = 25°C, unless otherwise noted)
INVERTER PART
Symbol
Parameter
Condition
VCE(sat)
VEC
ton
trr
tc(on)
toff
tc(off)
ICES
Collector-emitter saturation
voltage
FWD forward voltage
Switching times
Collector-emitter cut-off
current
VD = VDB = 15V
IC = 5A, Tj = 25°C
VCIN = 0V
IC = 5A, Tj = 125°C
Tj = 25°C, –IC = 5A, VCIN = 5V
VCC = 300V, VD = VDB =15V
IC = 5A, Tj = 125°C
Inductive load (upper-lower arm)
VCIN = 5 ↔ 0V
VCE = VCES
Tj = 25°C
Tj = 125°C
Limits
Unit
Min.
Typ. Max.
—
1.55 2.15
—
1.65 2.25
V
—
2.20 3.00
V
0.40
0.90
1.35
µs
—
0.20
—
µs
—
0.40
0.65
µs
—
1.2
1.65
µs
—
0.6
1.3
µs
—
—
—
—
1
mA
10
CONTROL (PROTECTION) PART
Symbol
Parameter
Condition
Limits
Min.
Typ.
Max. ^Unit
ID
Circuit current
VD = VDB =15V Total of VP1-VNC, VN1-VNC
—
VCIN = 5V
VUFB-VUFS, VVFB-VVFS, VWFB-VWFS —
VD = VDB =15V Total of VP1-VNC, VN1-VNC
—
VCIN = 0V
VUFB-VUFS, VVFB-VVFS, VWFB-VWFS —
—
8.5
mA
—
1.0
—
9.7
mA
—
1.0
VFOH
VFOL
VFOsat
VSC(ref)
UVDBt
Fault output voltage
Short-circuit trip level
VSC = 0V, FO = 10kΩ 5V pull-up
VSC = 0V, IFO = 1.5mA
VSC = 1V, IFO = 15mA
Tj = 25°C, VD = 15V
Trip level
4.9
—
—
V
—
0.6
0.9
V
0.8
1.2
1.8
V
(Note 4) 0.43 0.48 0.53
V
10.0
—
12.0
V
UVDBr
UVDt
UVDr
tFO
Vth(on)
Supply circuit under-voltage
protection
Fault output pulse width
ON threshold voltage
Tj ≤ 125°C
CFO = 22nF
Applied between:
Reset level
Trip level
Reset level
10.5
—
12.5
V
10.3
—
12.5
V
10.8
—
13.0
V
(Note 5)
1.0
1.8
—
ms
0.8
1.4
2.0
V
Vth(off)
OFF threshold voltage
UP, VP, WP-VNC, UN, VN, WN-VNC
2.5
3.0
4.0
V
Note 4 : Short-circuit protection operates only at the low-arms. Please select the value of the external shunt resistor such that the SC trip level
is less than 8.5A
5 : Fault signal is outputted when the low-arm short-circuit or control supply under-voltage protective functions operate. The fault output
pulse-width tFO depends on the capacitance value of CFO according to the following approximate equation. : CFO = (12.2 ✕ 10^-6) ✕ tFO [F]
Sep. 2001