PM75B5LB060_11 Datasheet, PDF (4/10 Pages) Mitsubishi Electric Semiconductor – FLAT-BASE TYPE INSULATED PACKAGE

MITSUBISHI <INTELLIGENT POWER MODULES>
PM75B5LB060
FLAT-BASE TYPE
INSULATED PACKAGE
CONVERTER PART
Symbol
VCE(sat)
VEC
VFM
ton
trr
tc(on)
toff
tc(off)
ICES
Parameter
Collector-Emitter
Saturation Voltage
FWDi Forward Voltage
Forward Voltage
Switching Time
Collector-Emitter
Cutoff Current
Condition
Min.
VD = 15V, IC = 75A
Tj = 25°C
—
VCIN = 0V, Pulsed
(Fig. 1) Tj = 125°C
—
–IC = 75A, VCIN = 15V, VD = 15V
(Fig. 2) —
IF = 75A
—
VD = 15V, VCIN = 0V↔15V
VCC = 300V, IC = 75A
Tj = 125°C
Inductive Load
0.3
—
—
—
(Fig. 3,4)
—
VCE = VCES, VD = 15V
Tj = 25°C
—
(Fig. 5)
Tj = 125°C
—
Limits
Typ.
1.7
1.55
2.2
1.9
0.7
0.1
0.2
0.9
0.2
—
—
Max. ^Unit
2.3
2.0
V
3.3
V
3.0
V
1.4
0.2
0.4
µs
1.8
0.4
1
10
mA
CONTROL PART
Symbol
Parameter
Condition
Limits
Min.
Typ.
Max. ^Unit
ID
Circuit Current
VD = 15V, VCIN = 15V
VN1-VNC
—
20
30
V*P1-V*PC
—
mA
6
12
Vth(ON) Input ON Threshold Voltage Applied between : UP-VUPC, VP-VVPC
Vth(OFF) Input OFF Threshold Voltage
UN • VN • WN-VNC
1.2
1.5
1.8
V
1.7
2.0
2.3
SC
Short Circuit Trip Level
Inverter part
–20 ≤ Tj ≤ 125°C, VD = 15V (Fig. 3,6)
150
—
Converter part 150
—
—
A
—
toff(SC)
Short Circuit Current Delay
Time
VD = 15V
(Fig. 3,6) —
0.2
—
µs
OT
VD = 15V
Over Temperature Protection
OTr
Detect Tj of IGBT chip
Trip level
Reset level
135
145
—
°C
—
125
—
UV
UVr
Supply Circuit Under-Voltage
Protection
–20 ≤ Tj ≤ 125°C
Trip level
Reset level
11.5
12.0 12.5
V
—
12.5
—
IFO(H)
IFO(L)
Fault Output Current
VD = 15V, VFO = 15V
(Note-2)
—
—
—
0.01
mA
10
15
tFO
Minimum Fault Output Pulse _{VD = 15V}
Width
(Note-2)
1.0
1.8
—
ms
(Note-2) Fault output is given only when the internal SC, OT & UV protections schemes of either upper or lower arm device operate to
protect it.
MECHANICAL RATINGS AND CHARACTERISTICS
Symbol
—
—
Parameter
Mounting torque
Weight
Mounting part
Condition
—
Limits
Min.
Typ.
Unit
Max.
screw : M5
2.5
3.0
3.5 N • m
—
340
—
g
RECOMMENDED CONDITIONS FOR USE
Symbol
Parameter
VCC
Supply Voltage
VD
Control Supply Voltage
VCIN(ON) Input ON Voltage
VCIN(OFF) Input OFF Voltage
Condition
Recommended value
Unit
Applied across P-N terminals
≤ 450
V
Applied between : VUP1-VUPC, VVP1-VVPC
VN1-VNC
(Note-3)
15 ± 1.5
V
Applied between : UP-VUPC, VP-VVPC
UN • VN • WN-VNC
≤ 0.8
V
≥ 9.0
fPWM
PWM Input Frequency
Using Application Circuit of Fig. 8
≤ 20
kHz
tdead
Arm Shoot-through
Blocking Time
For IPM’s each input signals
(Fig. 7)
≥ 2.0
µs
(Note-3) With ripple satisfying the following conditions : dv/dt swing ≤ ±5V/µs, Variation ≤ 2V peak to peak
Oct. 2005