PM300CBS060 Datasheet, PDF (4/6 Pages) Powerex Power Semiconductors – Intellimod™ Module MAXISS Series™ Multi AXIS Servo IPM (300 Amperes/600 Volts)

MITSUBISHI <INTELLIGENT POWER MODULES>
PM300CBS060
FLAT-BASE TYPE
INSULATED PACKAGE
CONTROL PART
Symbol
Parameter
Test Conditions
Limits
Min.
Typ.
Max. ^Unit
ID
Circuit Current
VD = 15V, VCIN = 15V
VN1-VNC
VXP1-VXPC
—
40
60
mA
—
13
18
Vth(ON) Input ON Threshold Voltage Applied between : UP-VUPC, VP-VVPC, WP-VWPC
1.2
1.5
1.8
V
Vth(OFF) Input OFF Threshold Voltage
UN • VN • WN-VNC
1.7
2.0
2.3
V
Over Current
OC
Trip Level
VD = 15V
Tj = –20°C
(Fig. 5,6) Tj = 25°C
Tj = 125°C
—
—
1430
612
855 1200
A
450
—
—
Short Circuit
SC
Trip Level
–20≤ Tj ≤ 125°C, VD = 15V (Fig. 5,6)
—
760
—
A
toff(OC) Over Current Delay Time
VD = 15V
(Fig. 5,6) —
10
—
µs
OT
OTr
Over Temperature protection Detect Tj of IGBT chip
Trip level
Reset level
135
145
155 °C
—
125
—
°C
UV
Supply Circuit Under-Voltage
UVr
Protection
–20 ≤ Tj ≤ 125°C
Trip level
Reset level
11.5
12.0 12.5
V
—
12.5
—
V
IFO(H)
IFO(L)
Fault Output Current
VD = 15V, VFO = 15V
—
(Note-2)
—
—
0.01 mA
10
15 mA
Minimum Fault Output Pulse
tFO
Width
VD = 15V
(Note-2) 1.0
1.8
—
ms
(Note-2) Fault output is given only when the internal OC, SC, OT & UV protection.
Fault output of OC, SC, OT & UV protection operate by lower arm.
Fault output of OC, SC protection given pulse.
Fault output of OT, UV protection given pulse while over trip level.
MECHANICAL RATINGS AND CHARACTERISTICS
Symbol
—
—
—
Parameter
Mounting torque
Mounting torque
Weight
Main terminal
Mounting part
Test Conditions
—
Limits
Min.
Typ.
Unit
Max.
screw : M5
2.5
3.0
3.5 N • m
screw : M5
2.5
3.0
3.5 N • m
—
680
—
g
RECOMMENDED CONDITIONS FOR USE
Symbol
Parameter
VCC
Supply Voltage
VD
Control Supply Voltage
VCIN(ON)
VCIN(OFF)
fPWM
tdead
Input ON Voltage
Input OFF Voltage
PWM Input Frequency
Arm Shoot-through
Blocking Time
Test Conditions
Recommended value
Unit
Applied across P-N terminals
≤ 400
V
Applied between : VUP1-VUPC, VVP1-VVPC
VWP1-VWPC, VN1-VNC
(Note-3)
15.0 ± 1.5
V
Applied between : UP-VUPC, VP-VVPC, WP-VWPC
≤ 0.8
V
UN • VN • WN-VNC
≥ 4.0
V
Using Application Circuit of Fig.8
≤ 20
kHz
For IPM’s each input signals
(Fig. 7)
≥ 2.5
µs
(Note-3) With ripple satisfying the following conditions
dv/dt swing ≤ ±5V/µs, Variation ≤ 2V peak to peak
Sep. 2001