PM10CNJ060 Datasheet, PDF (4/6 Pages) Mitsubishi Electric Semiconductor – INTELLIGENT POWER MODULES

MITSUBISHI <INTELLIGENT POWER MODULES>
PM10CNJ060
FLAT-BASE TYPE
INSULATED PACKAGE
CONTROL PART
Symbol
Parameter
Test Condition
Min.
ID
Circuit Current
VD = 15V, VCIN = 15V
VN1-VNC
—
VXP1-VXPC
—
Vth(ON) Input ON Voltage
Applied between : UP-VUPC, VP-VVPC, WP-VWPC
1.2
Vth(OFF) Input OFF Voltage
UN • VN • WN-VNC
1.7
OC
Over Current Trip Level
–20 ≤ Tj ≤ 125°C, VD = 15V
(Fig. 5,6)
12
SC
Short Circuit Trip Level
–20 ≤ Tj ≤ 125°C, VD = 15V
(Fig. 5,6) —
toff(OC)
Over Current Delay Time
VD = 15V
(Fig. 5,6) —
OT
Over Temperature protection VD = 15V
OTr
Trip level
100
Reset level
—
UV
Supply Circuit Under-Voltage
–20 ≤ Tj ≤ 125°C
UVr
Protection
Trip level
11.5
Reset level
—
IFO(H)
IFO(L)
Fault Output Current
VD = 15V, VCIN = 15V
(Note-2)
—
—
tFO
Minimum Fault Output Pulse _{VD = 15V}
Width
(Note-2) 1.0
Limits
Typ.
18
7
1.5
2.0
18
27
10
110
90
12.0
12.5
—
10
1.8
Unit
Max.
25
mA
10
1.8
V
2.3
V
—
A
—
A
—
µs
120
°C
—
°C
12.5
V
—
V
0.01 mA
15 mA
—
ms
(Note-2) Fault output is given only when the internal SC, OT & UV protections schemes of either upper or lower arm device operate to
protect it.
THERMAL RESISTANCES
Symbol
Parameter
Test Condition
Rth(j-c)Q
Rth(j-c)F
Rth(c-f)
Junction to case Thermal
Resistances
Contact Thermal Resistance
Inverter IGBT part (per 1/6 module)
Inverter FWDi part (per 1/6 module)
Case to fin, (per 1 module)
Thermal grease applied
Limits
Unit
Min.
Typ.
Max.
—
—
3.2 °C/W
—
—
4.5 °C/W
—
—
0.5 °C/W
MECHANICAL RATINGS AND CHARACTERISTICS
Symbol
Parameter
Test Condition
—
Mounting torque
—
Weight
Mounting part
—
screw : M4
Limits
Unit
Min.
Typ.
Max.
0.98 1.18 1.47 N • m
10
12
15 kg • cm
—
60
—
g
RECOMMENDED CONDITIONS FOR USE
Symbol
Parameter
VCC
Supply Voltage
VD
Control Supply Voltage
VCIN(ON)
VCIN(OFF)
fPWM
tdead
Input ON Voltage
Input OFF Voltage
PWM Input Frequency
Arm Shoot-through
Blocking Time
Test Condition
Applied across P-N terminals
(Fig. 3)
Applied between : VUP1-VUPC, VVP1-VVPC
VWP1-VWPC, VN1-VNC
(Note-3)
Applied between : UP-VUPC, VP-VVPC, WP-VWPC
UN • VN • WN-VNC
Using Application Circuit of Fig. 8
For IPM’s each input signals
(Fig. 7)
Recommended value
≤ 400
15 ± 1.5
≤ 0.8
≥ 4.0
≤ 15
≥2
Unit
V
V
V
kHz
µs
(Note-3) With ripple satisfying the following conditions
dv/dt swing ≤ ±5V/µs, Variation ≤ 2V peak to peak
Jan. 2000