PS11016 Datasheet, PDF (2/6 Pages) Powerex Power Semiconductors – FLAT-BASE TYPE INSULATED TYPE

MITSUBISHI SEMICONDUCTOR <Application Specific Intelligent Power Module>
PS11016
FLAT-BASE TYPE
INSULATED TYPE
INTERNAL FUNCTIONS BLOCK DIAGRAM
P
Brake resistor connection,
Inrush prevention circuit,
B
etc.
Application Specific Intelligent
Power Module
Protection
Circuit
Level shifter
Drive Circuit
AC 200V line input
R
S
T
U
V
W
M
ZC
Z : Surge absorber.
C : AC filter (Ceramic condenser 2.2~6.5nF)
[Note : Additionally an appropriate Line-to line
surge absorber circuit may become necessary
depending on the application environment].
T
N
S
Current sensing
circuit
Input signal conditioning
Drive Circuit
Fo Logic
Protection Control supply
circuit
fault sense
AC 200V line
output
CU CV CW
UP VP WP UN VN WN Br
Analogue signal output corresponding to PWM input
each phase current (5V line) Note 1) (5V line) Note 2)
CL, FO1, FO2, FO3
Fault output
(5V line) Note 3)
GND VDH
Note 1) To prevent chances of signal oscillation, a series resistor (1kΩ) coupling at each output is recommended.
Note 2) By virtue of integrating an photo-coupler inside the module, direct coupling to CPU, without any external opto or transformer isolation is possible.
Note 3) All outputs are open collector type. Each signal line should be pulled up to plus side of the 5V power supply with approximately 5.1kΩ resistance.
Note 4) The wiring between power DC link capacitor and P/N terminals should be as short as possible to protect the ASIPM against catastrophic high surge voltage.
For extra precaution, a small film snubber capacitor (0.1~0.22µF, high voltage type) is recommended to be mounted close to these P and N DC power input pins.
(Fig. 2)
MAXIMUM RATINGS (Tj = 25°C)
INVERTER PART (Including Brake Part)
Symbol
VCC
VCC(surge)
VP or VN
VP(S) or VN(S)
±IC(±ICP)
IC(ICP)
IF(IFP)
Item
Supply voltage
Supply voltage (surge)
Each output IGBT collector-emitter static voltage
Each output IGBT collector-emitter
switching surge voltage
Each output IGBT collector current
Brake IGBT collector current
Brake diode anode current
Condition
Applied between P-N
Applied between P-N, Surge-value
Applied between P-U, V, W, Br or U, V, W,
Br-N
Applied between P-U, V, W, Br or U, V, W,
Br-N
TC = 25°C
Note: “( )” means IC peak value
Ratings
Unit
450
V
500
V
600
V
600
V
±30 (±60)
A
15 (30)
A
15 (30)
A
CONTROL PART
Symbol
Item
VDH, VDB Supply voltage
VCIN
VFO
IFO
VCL
ICL
ICO
Input signal voltage
Fault output supply voltage
Fault output current
Current-limit warning (CL) output voltage
CL output current
Analogue current signal output current
Condition
Applied between VDH-GND, CBU+-CBU–,
CBV+-CBV–, CBW+-CBW–
Applied between UP · VP · WP · UN · VN ·
WN · Br-GND
Applied between FO1 · FO2 · FO3-GND
Sink current of FO1 · FO2 · FO3
Applied between CL-GND
Sink current of CL
Sink current of CU · CV · CW
Ratings
Unit
20
V
–0.5 ~ 7.5
V
–0.5 ~ 7
V
15
mA
–0.5 ~ 7
V
15
mA
±1
mA
Jan. 2000