M37735EHL Datasheet, PDF (13/34 Pages) Mitsubishi Electric Semiconductor – PROM VERSION OF M37735MHLXXXHP

PRELIMINARY _{NSootimcee: pTahriasmisentroict} ^{alimfinitsalasrpeescuifbicjeactitotno. change.}
MITSUBISHI MICROCOMPUTERS
M37735EHLXXXHP
PROM VERSION OF M37735MHLXXXHP
ABSOLUTE MAXIMUM RATINGS
Symbol
Vcc
AVcc
VI
VI
VO
Pd
Topr
Tstg
Parameter
Power source voltage
Analog power source voltage
_____
Input voltage RESET, CNVss, BYTE
Input voltage P00 – P07, P10 – P17, P20 – P27, P30 – P33,
P40 – P47, P50 – P57, P60 – P67, P70 – P77,
P80 – P87, VREF, XIN
Output voltage P00 – P07, P10 – P17, P20 – P27, P30 – P33,
P40 – P47, P50 – P57, P60 – P67, P70 – P77,
__
P80 – P87, XOUT, E
Power dissipation
Operating temperature
Storage temperature
Conditions
Ta = 25 °C
Ratings
Unit
–0.3 to +7
V
–0.3 to +7
V
–0.3 to +12 (Note)
V
–0.3 to Vcc + 0.3
V
–0.3 to Vcc + 0.3
V
200
mW
–40 to +85
°C
–65 to +150
°C
Note. When the EPROM is programmed, input voltage of pins CNVSS and BYTE is 13 V respectively.
RECOMMENDED OPERATING CONDITIONS (Vcc = 2.7 – 5.5 V, Ta = –40 to +85 °C, unless otherwise noted)
Symbol
Vcc
AVcc
Vss
AVss
VIH
VIH
VIH
VIL
VIL
VIL
IOH(peak)
IOH(avg)
IOL(peak)
IOL(peak)
IOL(avg)
IOL(avg)
f(XIN)
Parameter
Power source voltage
f(XIN) : Operating
f(XIN) : Stopped, f(XCIN) = 32.768 kHz
Analog power source voltage
Power source voltage
Analog power source voltage
High-level input voltage P00 – P07, P30 – P33, P40 – P47, P50 – P57, P60 – P67, P70 – P77,
_____
P80 – P87, XIN, RESET, CNVss, BYTE, XCIN (Note 3)
High-level input voltage P10 – P17, P20 – P27 (in single-chip mode)
High-level input voltage P10 – P17, P20 – P27
(in memory expansion mode and microprocessor mode)
Low-level input voltage P00 – P07, P30 – P33, P40 – P47, P50 – P57, P60 – P67, P70 – P77,
_____
P80 – P87, XIN, RESET, CNVss, BYTE, XCIN (Note 3)
Low-level input voltage P10 – P17, P20 – P27 (in single-chip mode)
Low-level input voltage P10 – P17, P20 – P27
(in memory expansion mode and microprocessor mode)
High-level peak output current P00 – P07, P10– P17, P20 – P27, P30 – P33,
P40 – P47, P50 – P57, P60 – P67, P70 – P77,
P80 – P87
High-level average output current P00 – P07, P10 – P17, P20 – P27, P30 – P33,
P40 – P47, P50 – P57, P60 – P67, P70 – P77,
P80 – P87
Low-level peak output current P00 – P07, P10 – P17, P20 – P27, P30 – P33,
P40 – P43, P54 – P57, P60 – P67, P70 – P77,
P80 – P87
Low-level peak output current P44 – P47, P50 – P53
Low-level average output current P00 – P07, P10 – P17, P20 – P27, P30 – P33,
P40 – P43, P54 – P57, P60 – P67, P70 – P77,
P80 – P87
Low-level average output current P44 – P47, P50 – P53
Main-clock oscillation frequency (Note 4)
Min.
2.7
2.7
0.8 Vcc
0.8 Vcc
0.5 Vcc
0
0
0
Limits
Typ.
Vcc
0
0
Max.
Unit
5.5
5.5
V
V
V
V
Vcc
V
Vcc
V
Vcc
V
0.2Vcc V
0.2Vcc V
0.16Vcc V
–10
mA
–5
mA
10
mA
16
mA
5
mA
12
mA
12 MHz
f(XCIN)
Sub-clock oscillation frequency
32.768
50 kHz
Notes 1. Average output current is the average value of a 100 ms interval.
2. The sum of IOL(peak) for ports P0, P1, P2, P3, and P8 must be 80 mA or less, the sum of IOH(peak) for ports P0, P1, P2, P3, and P8 must
be 80 mA or less, the sum of IOL(peak) for ports P4, P5, P6, and P7 must be 100 mA or less, and the sum of IOH(peak) for ports P4, P5,
P6, and P7 must be 80 mA or less.
3. Limits VIH and VIL for XCIN are applied when the sub clock external input selection bit = “1”.
4. The maximum value of f(XIN) = 6 MHz when the main clock division selection bit = “1”.
13