XG1001-SA Datasheet, PDF (1/6 Pages) Mimix Broadband – 100.05-4.0 GHz Dual High Dynamic Range Amplifier

0.05-4.0 GHz
Dual High Dynamic Range Amplifier
January 2010 - Rev 12-Jan-10
XG1001-SA
Features
Matched Pair of Amplifiers for Optimum Balanced Design _{Input 1}
0.05 to 4.0 GHz Frequency Range
Output 1
44 dBm Output IP3 (Balanced configuration)
41 dBm Output IP3 (Single-ended configuration)
N/C
N/C
13 dB Gain @ 2 GHz
22.5 dBm P1dBm
N/C
N/C
2.1 dB Noise Figure
RoHS Compliant SOIC-8 Package
Input 2
Output 2
Single Positive Supply
+3V to +5V Voltage Rail
General Description
The XG1001-SA is a dual high dynamic range amplifier designed for
applications operation within the 0.05 to 4.0 GHz frequency range.
Co-located matched amplifiers are assembled in an RoHS compliant
SOIC-8 package. The XG1001-SA is an ideal solution for
implementing balanced or push-pull designs. The amplifier can also
be used for dual-band operation where single-ended design is used
for each band. The amplifier has the flexibility of being optimized
for a number of wireless applications. The combination of low noise
figure and high IP3 at the same bias point make it an ideal transmit
or receive solution when used in applications including CATV
operating from 50 to 850 MHz, cellular and PCS (personal
communications service) operating from 0.8 to 2.2 GHz; MMDS
(multichannel multipoint distribution systems) operating from 2.2
to 2.7 GHz; and WLAN (wireless LAN) operation at 2.4 GHz. All
devices are 100% RF and DC tested.
Backside slug is source GND
Absolute Maximum Ratings
Supply Voltage
+6.0 V
RF Input Power*
+20 dBm
Storage Temperature (Tstg)
-55 ºC to +125 ºC
Junction Temperature
150 ºC
Operating Temperature
-40 ºC to +85ºC
Thermal Resistance
27 ºC/W
Operation of this device above any of these parameters may cause damage.
*Operation with more than 10 dBm of input power may cause 2 dB
degradation in OIP3 performance.
Typical Parameters
Parameter
Typical
Units
Frequency Range 0.9
2
2.4 GHz
Gain
14.5 13
12
dB
Input Return Loss -13 -14.5 -20 dB
Output Return Loss -16 -15.4 -11 dB
Output IP3
42
41 40.5 dBm
Noise Figure
2.1
2.1
2.6
dB
Output P1dB
+22.5 +22.5 +22.5 dBm
Electrical Characteristics ^{Typical values reflect performance in recommended application circuit @ +5V.}
(T = 25ºC)
Unless otherwise specified, the following specifications are guaranteed at room temerpature in a Mimix fixture.
Parameter
Condition
Units
Frequency Range
GHz
Gain
Externally Matched
dB
Input Return Loss
Externally Matched
dB
Output Return Loss
Externally Matched
dB
Output IP3
dBm
Noise Figure
dB
Output P1dB
dBm
Operating Current Range
mA
Supply Voltage
V
Notes:
1. T = 25ºC, Frequency = 2 GHz, 50 Ohm system.
2. Each single ended amplifier is tested separately.
3. OIP3 is measured with two tones at output power of 5 dBm/tone separated by 10 MHz.
4. Slight performance degredation is expected over temperature.
Min.
0.05
11.5
38
120
Typ.
13
-10
-10
41
2.1
22.5
160
5.0
Max.
4.0
200
Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099
Tel: [phone] Fax: [phone] mimixbroadband.com
Page 1 of 6
Characteristic Data and Specifications are subject to change without notice. ©2010 Mimix Broadband, Inc.
Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept
their obligation to be compliant with U.S. Export Laws.