CDQ6004-QS_07 Datasheet, PDF (1/10 Pages) Mimix Broadband – 0.05-4.0 GHz Dual High Dynamic Range Amplifier

0.05-4.0 GHz
Dual High Dynamic Range Amplifier
August 2007 - Rev 11-Aug-07
CDQ6004-QS
Features
Matched Pair of Amplifiers for Optimum Balanced Design
0.05 to 4.0 GHz Frequency Range
44 dBm Output IP3 (Balanced configuration)
41 dBm Output IP3 (Single-ended configuration)
15 dB Gain @ 2 GHz
23 dBm P1dBm
2.1 dB Noise Figure
RoHS Compliant 4X4 QFN Package
Single Positive Supply
+3V to +5V Voltage Rail
General Description
The CDQ6004-QS is a dual high dynamic range amplifier designed
Absolute Maximum Ratings
Supply Voltage
+6.0 V
for applications operation within the 0.05 to 4.0 GHz frequency
RF Input Power
+20 dBm
range. Co-located matched amplifiers are assembled in the 4mm X
Storage Temperature (Tstg)
-55 ºC to +125 ºC
4mm QFN package.The low-cost, surface-mount, 16 terminal, plastic
Junction Temperature
150 ºC
package is RoHS compliant. The CDQ6004-QS is an ideal solution for
Operating Temperature
-40 ºC to +85ºC
implementing balanced or push-pull designs. The amplifier can also
Thermal Resistance
52 ºC/W
be used for dual-band operation where single-ended design is used
Operation of this device above any of these parameters may cause damage.
for each band. The amplifier has the flexibility of being optimized
for a number of wireless applications. The combination of low noise
figure and high IP3 at the same bias point make it an ideal transmit
or receive solution when used in applications including CATV
operating from 50 to 850 MHz, cellular and PCS (personal
communications service) operating from 0.8 to 2.2 GHz; MMDS
(multichannel multipoint distribution systems) operating from 2.2
to 2.7 GHz; and WLAN (wireless LAN) operation at 2.4 GHz. All
devices are 100% RF and DC tested.
Typical Parameters
Parameter
Typical
Frequency Range 0.9
2
2.4
Gain
16.5 15 14.9
Input Return Loss -13 -11 -20
Output Return Loss -16 -12 -11
Output IP3
42
41 40.5
Noise Figure
2.1 2.1 2.6
Output P1dB
+23 +23 +24
Units
GHz
dB
dB
dB
dBm
dB
dBm
Electrical Characteristics (T = 25ºC) ^{Typical values reflect performance in recommended application circuit @ +5V.}
Unless otherwise specified, the following specifications are guaranteed at room temerpature in a Mimix fixture.
Parameter
Condition
Units Min. Typ. Max.
Frequency Range
GHz
0.25
3.0
Gain
Externally Matched
dB
13.5
15
Input Return Loss
Externally Matched
dB
-10
Output Return Loss
Externally Matched
dB
-10
Output IP3
dBm
38
41
Noise Figure
dB
2.1
Output P1dB
dBm
23
Operating Current Range
mA
130
160
200
Supply Voltage
V
5.0
Notes:
1. T = 25ºC, Frequency = 2 GHz, 50 Ohm system.
2. Each single ended amplifier is tested separately.
3. OIP3 is measured with two tones at output power of 5 dBm/tone separated by 10 MHz.
4. Slight performance degredation is expected over temperature.
Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099
Tel: [phone] Fax: [phone] mimixbroadband.com
Page 1 of 10
Characteristic Data and Specifications are subject to change without notice. ©2007 Mimix Broadband, Inc.
Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept
their obligation to be compliant with U.S. Export Laws.