SMP6LC50 Datasheet, PDF (1/2 Pages) Microsemi Corporation – TVSarray Series

8700 E. Thomas Road
Scottsdale, AZ 85252
Tel: [phone]
Fax: [phone]
DESCRIPTION (600 watt)
This 16 pin 2 line Bidirectional LOW CAPACITANCE array is designed for use
in applications where protection is required at the board level. Providing
protection from voltage transients caused by electrostatic discharge (ESD) as
defined in IEC 1000-4-2, electrical fast transients (EFT) per IEC 1000-4-4, and
effects of secondary lighting as stated by IEC 1000-4-5.
SMP6LC5.0
Thru
SMP6LC12
TVSarray™ Series
These TRANSIENT VOLTAGE SUPPRESSOR (TVS) Diode Arrays have a
peak power of 600 watts for an 10x1000 µsec pulse and are designed to be
used for secondary surge protection on telephone lines. This device can be
used in either common or differential mode applications. For example in the
circuit diagram on the following page use: TIP to (A) and (C) to ground, RING
to (B) and (D) to ground for common mode, or TIP to (A) and RING to (C), or
TIP to (B) and RING to (D) for differential mode.
FEATURES
• 600 watts Peak Pulse Power 10x1000
• Protects up through 12 Volt Components
• Protects 4 Unidirectional lines or 2 Bidirectional
Lines
• Provides electrically isolated protection
• SO-16 Packaging
• UL 94V-0 Flammability Classification
MAXIMUM RATINGS
• Operating Temperatures: -55⁰C to +150⁰C
• Storage Temperature: -55⁰C to +150⁰C
• Peak Pulse Power: 600 Watts (10/1000 µsec, Figure 1 and 2)
• Pulse Repetition Rate: <.01%
MECHANICAL
• Molded SO-16 Surface Mount
• Weight: 0.128 grams (approximate)
• Body Marked with Logo, and device number
• Pin #1 defined by DOT on top of package
PACKAGING
• Tape & Reel EIA Standard 481-1-A
• 13 inch reel 2,500 pieces (OPTIONAL
• Carrier tubes 50 pcs per (STANDARD)
ELECTRICAL CHARACTERISTICS PER LINE @ 25°C Unless otherwise specified
PART
NUMBER
DEVICE
MARKING
STAND-OFF
VOLTAGE
VWM
VOLTS
BREAKDOWN
VOLTAGE
VBR
@10 mA
VOLTS
CLAMPING
VOLTAGE
VC
@ IPP
VOLTS
MAXIMUM
LEAKAGE
CURRENT
@VWM
ID
µA
PEAK
PULSE
CURRENT
@ 10/1000 µS
IPP
AMPS
CAPACITANCE
(f=1 MHz)
@0V
C
PER LINE PAIR
pF
MAX
MIN
MAX
TYP
TYP
TYP
SMP6LC05 SMP6LC5.0
5.0
6.0
9.6
300
10
30
SMP6LC6.5 SMP6LC6.5
6.5
7.22
12.4
300
10
30
SMP6LC12 SMP6LC12
12.0
13.3
19.9
2.0
10
30
NOTE: Transient Voltage Suppression (TVS) product is normally selected based on its stand off voltage VWM. Product
selected voltage should be equal to or greater than the continuous or peak operating voltage of the circuit to be
protected.
Application: The SMP6LCXX product is designed for transient voltage suppression protection of components at the
board level. It is an ideal product to be used for protection of HIGH SPEED I/O TRANSCEIVERS.
MSC1379.PDF ISO 9001 CERTIFIED
REV C 10/15/99