1N935BUR-1_10 Datasheet, PDF (1/3 Pages) Microsemi Corporation – TEMPERATURE COMPENSATED ZENER REFERENCE DIODES

TECHNICAL DATA SHEET
6 Lake Street, Lawrence, MA 01841
1-800-446-1158 / [phone] / Fax: [phone]
Website: http: //www.microsemi.com
Gort Road Business Park, Ennis, Co. Clare, Ireland
Tel: [phone] Fax: [phone]
ZENER
– TEMPERATURE COMPENSATED ZENER REFERENCE DIODES
– LEADLESS PACKAGE FOR SURFACE MOUNT
– 9.0 VOLT NOMINAL ZENER VOLTAGE
– METALLURGICALLY BONDED, DOUBLE PLUG CONSTRUCTION
Qualified per MIL-PRF-19500/156
DEVICES
1N935BUR-1 thru 1N938BUR-1
CDLL935 thru CDLL938B
LEVELS
JAN
JANTX
JANTXV
JANS
MAXIMUM RATING AT 25°C
Operating Temperature: -65°C to +175°C
Storage Temperature: -65°C to +175°C
DC Power Dissipation: 500mW @ +50°C
Power Derating:
4mW / °C above +50°C
REVERSE LEAKAGE CURRENT
I_R = 10μA @ 25°C & V_R = 6Vdc
ELECTRICAL CHARACTERISTICS (T_A = 25°C, unless otherwise specified)
MIL-PRF-
19500/156
MSC
TYPE
NUMBER
ZENER
VOLTAGE
V_Z @ I_ZT
ZENER
TEST
CURRENT
I_ZT
MAXIMUM
ZENER
IMPEDACE
(Note 1)
Z_ZT
VOLTAGE
TEMPERATURE
STABILITY
3_{V ZT MAXIMUM}
(Note 2)
TEMPERATURE
RANGE
EFFECTIVE
TEMPERATURE
COEFFICIENT
VOLTS
mA
CDLL935 8.55 – 9.45
7.5
1N935BUR-1 CDLL935A 8.55 – 9.45
7.5
CDLL935B 8.55 – 9.45
7.5
CDLL936 8.55 – 9.45
7.5
1N936BUR-1 CDLL936A 8.55 – 9.45
7.5
CDLL936B 8.55 – 9.45
7.5
CDLL937 8.55 – 9.45
7.5
1N937BUR-1 CDLL937A 8.55 – 9.45
7.5
CDLL937B 8.55 – 9.45
7.5
CDLL938 8.55 – 9.45
7.5
1N938BUR-1 CDLL938A 8.55 – 9.45
7.5
CDLL938B 8.55 – 9.45
7.5
OHMS
20
20
20
20
20
20
20
20
20
20
20
20
mV
°C
% / °C
67
0 to + 75
0.01
139
-55 to +100
0.01
184
-55 to +150
0.01
34
0 to + 75
0.005
70
-55 to +100
0.005
92
-55 to +150
0.005
13
0 to + 75
0.002
28
-55 to +100
0.002
37
-55 to +150
0.002
6.7
0 to + 75
0.001
13.9
-55 to +100
0.001
19
-55 to +150
0.001
NOTE 1: Zener impedance is derived by superimposing on I_ZT A 60Hz rms a.c. current equal to 10% of I_ZT
NOTE 2: The maximum allowable change observed over the entire temperature range i.e., the diode voltage
will not exceed the specified mV at any discrete temperature between the established limits, per JEDEC
standard No. 5.
LDS-0158 Rev. 1 (100346)
DO-213AA
Page 1 of 3