|
1N5518B Datasheet, PDF (1/3 Pages) Microsemi Corporation – Low Voltage Avalanche 500 mW Zener Diodes DO-35 | |||
|
SCOTTSDALE DIVISION
1N5518B thru 1N5546B-1 DO-35
Low Voltage Avalanche
500 mW Zener Diodes DO-35
DESCRIPTION
The 1N5518 thru 1N5546 series of 0.5 watt Zener Voltage Regulators
provides a selection from 3.3 to 33 volts in standard 5% tolerances as well as
tighter tolerances identified by different suffix letters on the part number.
These glass axial-leaded DO-35 Zeners are also available with an internal-
metallurgical-bond option by adding a â-1â suffix. This type of bonded Zener
package construction is available in JAN, JANTX, and JANTXV military
qualifications to MIL-PRF-19500/437. Microsemi also offers numerous other
Zener products to meet higher and lower power applications.
IMPORTANT: For the most current data, consult MICROSEMIâs website: http://www.microsemi.com
APPEARANCE
DO-35
(DO-204AH)
FEATURES
⢠JEDEC registered 1N5518 thru 1N5546
⢠Internal metallurgical bond option available by
adding a â-1â suffix
⢠Also available in JAN, JANTX, and JANTXV
qualifications per MIL-PRF-19500/437 by adding the
JAN, JANTX, or JANTXV prefixes to part numbers
for desired level of screening as well as â1â suffix;
(e.g. JANTX1N5518B-1, JANTXV1N5546D-1, etc.)
⢠Military Surface Mount available in DO-213AA
package outline by adding a UR-1 suffix in addition
to the JAN, JANTX, and JANTXV prefix; e.g.
JANTX1N5518BUR-1 (see separate data sheet)
⢠Commercial Surface Mount also available in
separate data sheet as 1N5518UR to 1N5546BUR
in DO-213AA package (consult factory for others)
⢠DO-7 glass body axial-leaded Zener equivalents are
also available
APPLICATIONS / BENEFITS
⢠Regulates voltage over a broad operating
current and temperature range
⢠Guaranteed voltage regulation (âVZ) from IZL to IZT
⢠Voltage selection from 3.3 to 33 V
⢠Standard voltage tolerances are plus/minus 5%
with a âBâ suffix
⢠Tight tolerances available in plus or minus 2%
or 1% with C or D suffix respectively
⢠Flexible axial-lead mounting terminals
⢠Nonsensitive to ESD per MIL-STD-750 Method 1020
⢠Minimal capacitance (see Figure 3)
⢠Inherently radiation hard as described in Microsemi
MicroNote 050
MAXIMUM RATINGS
⢠Operating and Storage temperature: -65ºC to
+175ºC
⢠Thermal Resistance: 250 ºC/W junction to lead at
3/8 (10 mm) lead length from body, or 310ºC/W
junction to ambient when mounted on FR4 PC board
(1 oz Cu) with 4 mm2 copper pads and track width 1
mm, length 25 mm
⢠Steady-State Power: 0.5 watts at TL < 50oC 3/8 inch
(10 mm) from body or 0.48 W at TA < 25ºC when
mounted on FR4 PC board as described for thermal
resistance above (see Figure 2 for derating)
⢠Forward voltage @200 mA: 1.1 volts
⢠Solder Temperatures: 260 ºC for 10 s (max)
MECHANICAL AND PACKAGING
⢠CASE: Hermetically sealed axial-lead glass DO-35
(DO-204AH) package
⢠TERMINALS: Leads, tin-lead plated solderable per
MIL-STD-750, method 2026
⢠POLARITY: Cathode indicated by band where
diode is to be operated with the banded end
positive with respect to the opposite end for Zener
regulation
⢠MARKING: Part number
⢠TAPE & REEL option: Standard per EIA-296 (add
âTRâ suffix to part number)
⢠WEIGHT: 0.2 grams
⢠See package dimensions on last page
Copyright  2003
11-12-2003 REV B
Microsemi
Scottsdale Division
8700 E. Thomas Rd. PO Box 1390, Scottsdale, AZ 85252 USA, (480) 941-6300, Fax: (480) 947-1503
Page 1
|
▷ |