1N4614UR-1 Datasheet, PDF (1/2 Pages) Microsemi Corporation – LEADLESS PACKAGE FOR SURFACE MOUNT

• 1N4614UR-1 THRU 1N4627UR-1 AVAILABLE IN JAN, JANTX, JANTXV AND
JANS
PER MIL-PRF-19500/435
• LEADLESS PACKAGE FOR SURFACE MOUNT
• LOW CURRENT OPERATION AT 250 µA
• METALLURGICALLY BONDED
1N4614UR-1
thru
1N4627UR-1
and
CDLL4614 thru CDLL4627
MAXIMUM RATINGS
Operating Temperatures: -65°C to +175°C
DC Power Dissipation: 500mW @ TEC = +125°C
Power Derating: 10 mW / °C above TEC = +125°C
Forward Voltage @ 200 mA: 1.1 Volts maximum
ELECTRICAL CHARACTERISTICS @ 25°C, unless otherwise speci½ed.
CDI
TYPE
NUMBER
CDLL4614
CDLL4615
CDLL4616
CDLL4617
CDLL4618
CDLL4619
CDLL4620
CDLL4621
CDLL4622
CDLL4623
CDLL4624
CDLL4625
CDLL4626
CDLL4627
NOMINAL
ZENER
VOLTAGE
V @I
Z ZT
(Note 1)
VOLTS
1.8
2.0
2.2
2.4
2.7
3.0
3.3
3.6
3.9
4.3
4.7
5.1
5.6
6.2
ZENER
TEST
CURRENT
I
ZT
µA
250
250
250
250
250
250
250
250
250
250
250
250
250
250
MAXIMUM
ZENER
IMPEDANCE
Z @I
ZT ZT
(Note 2)
OHMS
1200
1250
1300
1400
1500
1600
1650
1700
1650
1600
1550
1500
1400
1200
MAXIMUM REVERSE
LEAKAGE CURRENT
1 @V
RR
µA
VOLTS
7.5
1
5.0
1
4.0
1
2.0
1
1.0
1
0.8
1
7.5
1.5
7.5
2
5.0
2
4.0
2
10.0
3
10.0
3
10.0
4
10.0
5
MAXIMUM
DC ZENER
CURRENT
mA
120
110
100
95
90
87
85
83
80
77
75
70
65
61
NOTE 1
NOTE 2
The CDI type numbers shown above have a Zener voltage tolerance of +5.0%.
Nominal Zener voltage is measured with the device junction in thermal
equilibrium at an ambient temperature of 25°C + 3°C. "C" suffix denotes a + 2%
tolerance and "D" suffix denotes a + 1% tolerance.
Zener impedance is derived by superimposing on 1ZT A 60Hz rms a.c. current equal to
10% of IZT.
MILLIMETERS INCHES
DIM MIN MAX MIN MAX
D 1.60 1.70 0.063 0.067
F 0.41 0.55 0.016 0.022
G 3.30 3.70 .130 .146
G1 2.54 REF. .100 REF.
S
0.03 MIN. .001 MIN.
FIGURE 1
DESIGN DATA
CASE: DO-213AA, Hermetically sealed
glass case. (MELF, SOD-80, LL34)
LEAD FINISH: Tin / Lead
THERMAL RESISTANCE: (ROJEC):
100 °C/W maximum at L = 0 inch
THERMAL IMPEDANCE: (ZJX): 35
°C/W maximum
POLARITY: Diode to be operated with
the banded (cathode) end positive.
MOUNTING SURFACE SELECTION:
The Axial Coefficient of Expansion
(COE) Of this Device is Approximately
+6PPM/°C. The COE of the Mounting
Surface System Should Be Selected To
Provide A Suitable Match With This
Device.
6 LAKE STREET, LAWRENCE, MASSACHUSETTS 01841
PHONE [phone]
FAX [phone]
WEBSITE: http://www.microsemi.com
123