IB-XLS-1W Datasheet, PDF (2/2 Pages) Microdc power Technology Co., Ltd – FIXED INPUT,ISOLATED & REGULATED Single Output DC/DC Converter

IB-XLS-1W&IB-XLD-1W Series
TEMPERATURE CHARACTERISTICS
Parameter
Conditions
Min.
Typ.
Max.
Storage humidity range
Operating temperature
Storage temperature
Lead temperature
Temp.rise at full load
Cooling
Case material
1.5mm from case for 10 seconds
Short circuit protection
MTBF
Weight
-40
-55
3500
95
80
125
15
25
300
Free air convection
Plastic(UL94-V0)
Continuous
1
2.1
*Supply voltage must be discontinued at the end of short circuit duration.
TYPICAL CHARACTERISTICS
Temperature Derating Graph
Units
%
°C
°C
°C
°C
S
K hours
g
APPLICATION NOTE
Requirement on output load
To ensure this module can operate efficiently and
reliably, During operation,the minimum output load is not
less than 10% of the full load,and that this product
should never be operated under no load!If the actual
output power is very small, please connect a resistor
with proper resistance at the output end in parallel to
increase the load,or use our company's products with
a lower rated output power(IB_XLD -W25/IB_XLS-W25
series).
Recommended circuit
If you want to further decrease the input/output ripple,
an "LC" filtering network may be connected to the input
and output ends of the DC/DC converter, see (Figure 1).
It should also be noted that the inductance and the
frequency of the "LC" filtering network should be
staggered with the DC/DC frequency to avoid mutual
interference. However, the capacitance of the output
filter capacitor must be proper. If the capacitance is too
big, a startup problem might arise. For every channel of
output, provided the safe and reliable operation is
ensured, the greatest capacitance of its filter capacitor
sees (Table 1).
OUTLINE DIMENSIONS & PIN CONNECTIONS
IB-XLS-1W
SIZE Graph
IB-XLD-1W
EXTERNAL CAPACITOR TABLE (TABLE 1)
Vin
Cin
Vout
(VDC)
(μF)
(VDC)
5
4.7
5
12
2.2
9
15
1
12
24
0.47
15
Cout
(μF)
10
4.7
2.2
1
It's not recommend to connect any external capacitor in
the application field with less than 0.5 watt output.
Note:
Unit:mm(inch)
Pin section:0.50*0.3mm(0.020*0.012inch)
Pin section tolerances: ±0.10mm(±0.004inch)
General tolerances: ±0.25mm(±0.010inch)
FOOTPRINT DETAILS
Pin
SIP
1
VIN
2
GND
4
0V
6
+V0
RECOMMENDED FOOTPRINT
Top view,grid:2.54mm(0.1inch)
diameter:1.00mm(0.039inch)
FOOTPRINT DETAILS
Pin
SIP
1
GND
7
NC
9
+V0
11
0V
14
VIN
NC:No Connection
All specifications typical at TA=25°C, nominal input voltage and rated output current unless otherwise
specified.Another 24V products, please inquire Our technical department!
Requirement on output load
To ensure this module can operate efficiently and reliably, During operation, the minimum output load is
not less than 10% of the full load, and that this product should never be operated under no load! If the
actual output power is very small, please connect a resistor with proper resistance at the output end in
parallel to increase the load.or use our company's products with a lower rated output power .
Overload Protection
Under normal operating conditions, the output circuit of
these products has no protection against over-current
and short-circuits.The simplest method is to connect a
self-recovery fuse in series at the input end or add a
circuit breaker to the circuit.
When the environment temperature is higher than
71°C, the product output power should be less then
60% of the rated power.
No parallel connection or plug and play.
Use dual output simultaneously, forbid opening output
pin(0V)to use as single output.
Microdc Professional Power Module,Inc.
Tel:[phone] E-mail:[e-mail]
Website:http://www.microdc.cn
RoHS COMPLIANT INFORMATION
This series is compatible with RoHS soldering systems with a peak wave solder temperature
of 300°C for 10 seconds.
The pin termination finish on the SIP package type is Tin Plate, Hot Dipped over Matte Tin
with Nickel Preplate. The DIP types are Matte Tin over Nickel Preplate. Both types in this
series are backward compatible with Sn/Pb soldering systems.
REACH COMPLIANT INFORMATION
This series has proven that this product does not contain harmful chemicals, it also has
harmful chemical substances through the registration, inspection and approval.
http://www.microdc.cn Technical Enquiries-Email:[e-mail] Tel:[phone] Page 2 of 2