|
PIC16LF1847_13 Datasheet, PDF (350/440 Pages) Microchip Technology – 18/20/28-Pin Flash Microcontrollers with XLP Technology | |||
|
◁ |
PIC16(L)F1847
30.2 DC Characteristics: Supply Current (IDD)
PIC16LF1847
PIC16F1847
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C ï£ TA ï£ +85°C for industrial
-40°C ï£ TA ï£ +125°C for extended
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C ï£ TA ï£ +85°C for industrial
-40°C ï£ TA ï£ +125°C for extended
Param.
No.
Device
Characteristics
Min. Typâ Max. Units
VDD
Conditions
Note
Supply Current (IDD) (Note 1, 2)
D010
â
9.5
14
ïA
1.8 FOSC = 32 kHz
â
12.5
17
ïA
3.0 LP Oscillator
-40°C ï£ TA ï£ï +85°C
D010
â
22
29
ïA
1.8 FOSC = 32 kHz
â
27
35
ïA
3.0 LP Oscillator
-40°C ï£ TA ï£ï +85°C
â
30
38
ïA
5.0
D010A
â
9.5
14
ïA
1.8 FOSC = 32 kHz
â
12.5
17
ïA
3.0 LP Oscillator
-40°C ï£ TA ï£ï +125°C
D010A
â
22
29
ïA
1.8 FOSC = 32 kHz
â
27
35
ïA
3.0 LP Oscillator
-40°C ï£ TA ï£ï +125°C
â
30
38
ïA
5.0
D011
â
105
110
ïA
â
160
190
ïA
1.8 FOSC = 1 MHz
3.0 XT Oscillator
D011
â
132
154
ïA
â
186
220
ïA
1.8 FOSC = 1 MHz
3.0 XT Oscillator
â
216
290
ïA
5.0
D012
â
264
370
ïA
â
491
620
ïA
1.8 FOSC = 4 MHz
3.0 XT Oscillator
D012
â
285
300
ïA
â
408
600
ïA
1.8 FOSC = 4 MHz
3.0 XT Oscillator
â
490
700
ïA
5.0
D013
â
55
160
ïA
1.8 FOSC = 1 MHz
â
90
230
ïA
3.0 EC Oscillator
Medium-power mode
D013
â
75
95
ïA
â
116
130
ïA
â
145
185
ïA
1.8 FOSC = 1 MHz
3.0 EC Oscillator
Medium-power mode
5.0
* These parameters are characterized but not tested.
â Data in âTypâ column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are not
tested.
Note 1: The test conditions for all IDD measurements in active operation mode are: OSC1 = external square wave, from
rail-to-rail; all I/O pins tri-stated, pulled to VDD; MCLR = VDD; WDT disabled.
2: The supply current is mainly a function of the operating voltage and frequency. Other factors, such as I/O pin loading
and switching rate, oscillator type, internal code execution pattern and temperature, also have an impact on the current
consumption.
3: 8 MHz internal oscillator with 4x PLL enabled.
4: 8 MHz crystal oscillator with 4x PLL enabled.
5: For RC oscillator configurations, current through REXT is not included. The current through the resistor can be extended
by the formula IR = VDD/2REXT (mA) with REXT in kïï®
DS40001453D-page 350
Preliminary
ï£ 2011-2013 Microchip Technology Inc.
|
▷ |