93C46B Datasheet, PDF(3/12 Page) Microchip Technology

English

English German Russian Spanish Italian Polish Chinese Japanese Korean French Portuguese	Language :

93C46B Datasheet, PDF (3/12 Pages) Microchip Technology – 1K 5.0V Microwire Serial EEPROM

◁

93C46B

2.0 PIN DESCRIPTION

2.1 Chip Select (CS)

A high level selects the device; a low level deselects the

device and forces it into standby mode. However, a pro-

gramming cycle which is already in progress will be

completed, regardless of the Chip Select (CS) input

signal. If CS is brought low during a program cycle, the

device will go into standby mode as soon as the pro-

gramming cycle is completed.

CS must be low for 250 ns minimum (TCSL) between

consecutive instructions. If CS is low, the internal con-

trol logic is held in a RESET status.

2.2 Serial Clock (CLK)

The Serial Clock (CLK) is used to synchronize the com-

munication between a master device and the 93C46B.

Opcodes, addresses, and data bits are clocked in on

the positive edge of CLK. Data bits are also clocked out

on the positive edge of CLK.

CLK can be stopped anywhere in the transmission

sequence (at high or low level) and can be continued

anytime with respect to clock high time (TCKH) and

clock low time (TCKL). This gives the controlling master

freedom in preparing the opcode, address, and data.

CLK is a âDon't Careâ if CS is low (device deselected).

If CS is high, but START condition has not been

detected, any number of clock cycles can be received

by the device, without changing its status (i.e., waiting

for a START condition).

CLK cycles are not required during the self-timed

WRITE (i.e., auto ERASE/WRITE) cycle.

After detecting a START condition, the speciï¬ed num-

ber of clock cycles (respectively low to high transitions

of CLK) must be provided. These clock cycles are

required to clock in all required opcodes, addresses,

and data bits before an instruction is executed

(Table 2-1). CLK and DI then become don't care inputs

waiting for a new START condition to be detected.

Note: CS must go low between consecutive

instructions.

2.3 Data In (DI)

Data In (DI) is used to clock in a START bit, opcode,

address, and data synchronously with the CLK input.

2.4 Data Out (DO)

Data Out (DO) is used in the READ mode to output data

synchronously with the CLK input (TPD after the posi-

tive edge of CLK).

This pin also provides READY/BUSY status information

during ERASE and WRITE cycles. READY/BUSY sta-

tus information is available on the DO pin if CS is

brought high after being low for minimum chip select

low time (TCSL) and an ERASE or WRITE operation has

been initiated.

The status signal is not available on DO, if CS is held

low during the entire ERASE or WRITE cycle. In this

case, DO is in the HIGH-Z mode. If status is checked

after the ERASE/WRITE cycle, the data line will be high

to indicate the device is ready.

TABLE 2-1

Instruction

ERASE

ERAL

EWDS

EWEN

READ

WRITE

WRAL

INSTRUCTION SET FOR 93C46B

SB Opcode

Address

A5 A4 A3 A2 A1 A0

1 0XXXX

0 0XXXX

1 1XXXX

A5 A4 A3 A2 A1 A0

0 1XXXX

Data In

D15 - D0

Data Out

(RDY/BSY)

HIGH-Z

D15 - D0

(RDY/BSY)

Req. CLK Cycles

Preliminary

DS21172D-page 3

▷