93AA86A_12 Datasheet, PDF (3/38 Pages) Microchip Technology – 16K Microwire Compatible Serial EEPROM

93AA86A/B/C, 93LC86A/B/C, 93C86A/B/C
1.0 ELECTRICAL CHARACTERISTICS
Absolute Maximum Ratings ^(†)
VCC............................................................................................................................................................................. 7.0V
All inputs and outputs w.r.t. VSS ..........................................................................................................-0.6V to VCC +1.0V
Storage temperature ...............................................................................................................................-65°C to +150°C
Ambient temperature with power applied................................................................................................-40°C to +125°C
ESD protection on all pins  4 kV
Note:
† NOTICE: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent dam-
age to the device. This is a stress rating only and functional operation of the device at those or any other
conditions above those indicated in the operational listings of this specification is not implied. Exposure to
maximum rating conditions for extended periods may affect device reliability.
TABLE 1-1: DC CHARACTERISTICS
All parameters apply over the specified
ranges unless otherwise noted.
Industrial (I): TA = -40°C to +85°C, VCC = +1.8V to 5.5V
Automotive (E): TA = -40°C to +125°C, VCC = +2.5V to 5.5V
Param.
No.
Symbol
Parameter
Min. Typ. Max. Units
Conditions
D1
VIH1
High-level input voltage
2.0
— VCC +1 V VCC 2.7V
VIH2
0.7 VCC — VCC +1 V VCC < 2.7V
D2
VIL1
Low-level input voltage
VIL2
-0.3
—
0.8
V VCC 2.7V
-0.3
— 0.2 VCC V VCC < 2.7V
D3
VOL1 Low-level output voltage
VOL2
—
—
0.4
V IOL = 2.1 mA, VCC = 4.5V
—
—
0.2
V IOL = 100 A, VCC = 2.5V
D4
VOH1 High-level output voltage
2.4
—
—
VOH2
VCC - 0.2 —
—
V IOH = -400 A, VCC = 4.5V
V IOH = -100 A, VCC = 2.5V
D5
ILI
Input leakage current
—
—
±1
A VIN = VSS or VCC
D6
ILO
Output leakage current
—
—
±1
A VOUT = VSS or VCC
D7
CIN,
Pin capacitance (all inputs/ —
—
7
pF VIN/VOUT = 0V (Note 1)
COUT outputs)
TA = 25°C, FCLK = 1 MHz
D8
ICC write Write current
—
—
3
mA FCLK = 3 MHz, VCC = 5.5V
—
500
—
A FCLK = 2 MHz, VCC = 2.5V
D9
ICC read Read current
—
—
1
mA FCLK = 3 MHz, VCC = 5.5V
—
—
500
A FCLK = 2 MHz, VCC = 3.0V
—
100
—
A FCLK = 2 MHz, VCC = 2.5V
D10 ICCS
Standby current
—
—
1
A I – Temp
—
—
5
A E – Temp
CLK = CS = 0V
ORG = DI
PE = VSS or VCC
(Note 2) (Note 3)
D11 VPOR VCC voltage detect
—
1.5
—
—
3.8
—
(Note 1)
V 93AA86A/B/C, 93LC86A/B/C
V 93C86A/B/C
Note 1: This parameter is periodically sampled and not 100% tested.
2: ORG and PE pin not available on ‘A’ or ‘B’ versions.
3: Ready/Busy status must be cleared from DO; see Section 3.4 “Data Out (DO)”.
 2003-2012 Microchip Technology Inc.
DS21797L-page 3